Teac R-999X Bedienungsanleitung Seite 2

Table of Contents
Thanks for Buyinga TEAC . . 2
Voltage Conversion wundie 2
Environmetal Considerations ...... . 4
Introduction
Useitnow.............00. 4
Connections... . 5
Cassette Tape... wis 5
Features and Controls . . . 5
Playback and Recording 8
Special Techniques and Features . . 9 — 13
Setting the Recording Level, Punch-in
Recording, Multi-Counter Function, CPS
(Computomatic Program Search), CDS
(Computomatic Direct Selection), REC
MUTE Function, Dubbing, Erasing, dbx
Disc Recording, Calibration Procedures,
BLOCK REPEAT Operation, Timer-
Controlled Operation, Real-Time
Reverse and End Stop, Three-Head
System, Dolby B, C and dbx Noise
Reduction Systems
Maintenance................. 13
Troubleshooting. .............. 13
Specifications... ............. 13
Reference Illustrations (Fig.1,2)..... 3
Reference Illustrations (Fig.3,4,5,6) . . 64
As you are reading through this manual, it
will help if you refer to page 3 and 64 as a
handy pictorial guide.
Thanks for Buying a TEAC
SSS
This deck was built to the highest standards
under strict quality control to give years of
faultless service.
It features bi-directional recording and auto
reverse/repeat playback, dbx** and Dolby*
B, C NR systems, a PEAK PROGRAM
LEVEL METER, BLANK SCAN, CPS,
BIAS and LEVEL CALIBRATION, MULTI
DISPLAY (conventional tape counter, TRT
counter), etc.
To be sure that you get the best from your
deck and discover its full potential, read
through this manual carefully. We wish you
success and contentment with your new
deck.
fi
Voltage conversion (Refer to Fig. 3)
General Export Models Only:
This unit is adjusted to operate on the
electric voltage specified on the unit or
packing carton.
Note: This voltage conversion is not possible
on models sold in the U.S.A., Canada, and
UK, Australia or Europe.
For general export units, if it is necessary to
change the voltage requirements of the deck
to match your area, use the following
procedures. Always disconnect Power Line
Cord before making these changes.
1, Locate the voltage selector on the rear
panel of the deck as shown in the
illustration.
2. Using a regular screwdriver, turn the
selector until the numerals correspond-
ing to the voltage requirements of your
area appear.
PERSONNEL.
| CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
The lightning flash with arrowhead symbol within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage' within the product's enclosure, that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
appliance.
The exclamation point within an equilateral triangle is intended to
alert the user of the presence of important operating and mainten-
ance (servicing) instructions in the literature accompanying the
H This cassette deck has a serial number
_ located on the rear panel. Please record
| the model number and serial number and
| retain them for your records.
" Model number
Serial number.
*
Dolby noise reduction manufactured
under license from Dolby Laboratories
Licensing Corporation. "Dolby" and the
double-D symbol are trademarks of
Dolby Laboratories Licensing Corpora-
tion,
WARNING:
TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
** dbx is a trademark of dbx Incorporated.
dbx noise reduction system manufactur-
ed under license from dbx Incorporated.
This product is manufactured to comply
with the radio interference of EEC direc-
tive '82/499/EEC."
pe
Note for U.K. Customers
aS
U.K. Customers only: Due to the variety of
plugs being used in the U.K., this unit is sold
without an AC plug. Please request your
dealer to install the correct plug to match
the mains power outlet where your unit wil
be used as per these instructions.
IMPORTANT
The wires in this mains lead are coloured
in accordance with the following code:
BLUE:
BROWN:
NEUTRAL
LIVE
As the colours of the wires in the mains
lead of this apparatus may not corres-
pond with coloured markings indentify-
ing the terminals in your plug, proceed
as follows.
The wire which is coloured BLUE must
be connected to the terminal which is
marked with the letter N or coloured
BLACK. The wire which is coloured
BROWN must be connected to the
terminal which is marked with the letter
L or coloured RED.