Scheppach TS310 Original Bedienungsanleitung Seite 26

– Only use saw blades recommended by the manu-
facturer which conform to EN 847-1. m Warning!
Keep attention When changing the saw blade.
The cutting width is not smaller and the main
blade thickness of the saw blade is not greater
than the thickness of the gap wedge!
– Make sure that a suitable saw blade for the mate-
rial to be cut is selected.
– Wear suitable personal protective equipment.
This includes:
Hearing protection to avoid the risk of becoming
hearing impaired,
Respiratory protection to avoid the risk of inhaling
harmful dust,
– Wear gloves when handling saw blades and rough
materials.
– Carry saw blades in a container whenever practi-
cal.
– Wear goggles. Sparks generated during work or
splinters, chippings and dust coming from the
device can lead to loss of eyesight.
– Connect a dust collecting device to the electric
tool when sawing wood. The emission of dust is
influenced, among other things, by the type of
material to be processed, the significance of local
separation (collection or source) and the correct
setting of the hood/guide plates/guides.
– Do not use saw blades made of high-speed alloy
steel (HSS steel).
– In times of non-use keep the push stick or the
push block with the electrical power tool in its
holder at all times.
Maintenance and repair
– Pull out the mains plug for any adjustment or re-
pair tasks.
– The generation of noise is influenced by vari-
ous factors, including the characteristics of saw
blades, condition of saw blade and electric tool.
Use saw blades which were designed for reduced
noise development, insofar as possible. Maintain
the electric tool and tool attachments regularly
and if necessary, initiate repairs in order to re-
duce noise.
– Report faults on the electric tool, protective de-
vices or the tool attachment to the person respon-
sible for safety as soon as they are discovered.
Safe work
– Use the push stick or handle with sliding wood,
to pass the workpiece securely out off the saw
blade.
– Make sure that the riving knife is always used,
and set up is correctly.
– Use the upper blade guard and set it to the cor-
rect position.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
– Only use saw blades for which the maximum per-
missible speed is not lower than the maximum
spindle speed of table saws and which are suit-
able for the material to be cut.
– Do not cut rebates or grooves without fitting a
suitable guard, e.g. a tunnel-type guard, over the
saw table.
– Circular saws must not be used for slotting jobs
(cutting grooves which end in the workpiece).
– When transporting the electric tool, only use the
transport devices. Never use the protective de-
vices for handling or transport.
– Make sure that the upper part of the saw blade
is covered during transport, e.g. by the protec-
tive device.
– Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for the
intended purpose.
– The floor around the machine must be level, clean
and free of loose particles, such as chips and
cutting residues.
– Always stand to the side of the saw blade when
working with the saw.
– Do not remove any cutting residues or other parts
of workpieces from the cutting zone while the
machine is running and the saw unit is not at rest.
– Make sure that the machine is always secured on
a workbench or a table if at all possible.
– Support long workpieces (e.g. with a roller table)
to prevent them sagging at the end of a cut.
– m Attention! Never remove loose splinters, chips
or jammed pieces of wood while the saw blade is
running.
• Switch off the machine to troubleshoot or remove
jammed pieces of wood. - Disconnect the main
power plug -
• Refitting, including adjusting and measuring
works, and cleaning must be carried out only
when the motor is switched off. - Disconnect the
main power plug -
• Before switching on again, ensure that keys and
adjustment tools have been removed.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Safety instructions for the handling of saw blades
1 Only use insertion tools if you have mastered
their use.
2 Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.