Abiomed Impella 5.0 Gebrauchsanweisung Seite 8

6
When the Impella 5.0 Catheter is not properly placed across the aortic valve, or when it is fully in the aorta or fully
®
in the ventricle, the pressures outside and inside the cannula are the same throughout the cardiac cycle. As a result,
the pressure on either side of the sensor membrane is the same, resulting in a flat placement signal.
2016-07-22 10:09
Impella 5.0 S/N: 123456 Impella S/N 123456 30 - 06 - 2011 05:30 21 - 12 - 2010 05:30
1. Reduce the P-level to P-2 until imaging is available.
Impella Position Wrong
2. Reposition with imaging.
3. Return to preferred P-level and confirm positioning with imaging.
Impella Position
Wrong
Impella Flow Impella Flow Purge System Purge System System Power System Power
5.0 5.0
5.2 Max Purge Flow: 20.0 ml/hr
Purge Flow: 20.0 ml/hr
L/min -.-
________________________
4.8 Min Time Remaining: 021:52
L/min Purge Pressure: 600 mmHg 100% 100%
PURGE CASSETTE
Do not use saline in the purge system.
The purge cassette delivers rinsing fluid to the Impella
solution) flows from the purge cassette through the catheter to the microaxial blood pump to prevent blood from
entering the motor.
ACCESSORIES
AIC SN: IC4186 V5.1
Impella 5.0 S/N: 123456 Impella S/N 123456
Impella Position Wrong
MUTE
MUTE
ALARM ALARM
60
FLOW
P-LEVEL
CONTROL
P-8
0.0 5.0
P-8 0.0
DISPLAY DISPLAY
-20
1000
PURGE PURGE
SYSTEM
SYSTEM
0
Impella Flow Impella Flow
MENU
MENU
5.0 5.0
5.2 Max
________________________
4.8 Min
® 5.0 Catheter. The purge fluid (typically 5% dextrose
The white connector cable connects the Impella
Impella Controller. Clips on the cable are used to secure the purge tubing to the
®
cable.
• The socket at the black end of the cable connects to the red Impella
• The white plug at the opposite end of the cable is inserted into the blue catheter
plug on the front of the Automated Impella
The silicone plugs may be attached to the shaft of the Impella
in inserting the catheter.
2016-07-22 10:09 AIC SN: IC4186 V5.1
30 - 06 - 2011 05:30 21 - 12 - 2010 05:30
1. Reduce the P-level to P-2 until imaging is available.
2. Reposition with imaging.
3. Return to preferred P-level and confirm positioning with imaging.
Placement
P-LEVEL
CONTROL
Signal
(mmHg)
6/2
(2)
DISPLAY DISPLAY
10 sec.
Motor
Current
(mA)
801/800
SYSTEM
SYSTEM
(800)
10 sec.
Purge System Purge System System Power System Power
Purge Flow: 20.0 ml/hr
Purge Flow: 20.0 ml/hr
Time Remaining: 021:52
L/min Purge Pressure: 600 mmHg 100% 100%
5.0 Catheter to the Automated
®
plug.
®
® Controller.
5.0 Catheter to aid
®
User Manual
MUTE
MUTE
ALARM ALARM
FLOW
P-8
0.0 0.0
P-8 0.0
PURGE PURGE
MENU MENU