Abbildungsverzeichnis - CSM ECAT STGMM 6 Bedienungsanleitung

ECAT STGMM 6
Anhang
7.2

Abbildungsverzeichnis

Abb. 3-1: ECAT STGMM 6, Frontansicht (Slide Case SCL) ................................................................. 7
Abb. 3-2: ECAT STGMM 6, Gehäuserückseite (Slide Case SCL) ....................................................... 7
Abb. 4-1: Anschlussschema Vollbrücke in 4-Leiter-Technik ............................................................... 16
Abb. 4-2: Anschlussschema Vollbrücke in 6-Leiter-Technik ............................................................... 17
Abb. 4-3: Anschlussschema Halbbrücke ............................................................................................ 18
Abb. 4-4: Anschlussschema Halbbrücke mit "Free Factor" ................................................................ 19
Abb. 5-1: Messaufbau mit drei ECAT STGMM 6 und einem XCP-Gateway ...................................... 22
Abb. 5-2: Dialog Eigenschaften Internetprotokoll Version 4 (TCP/IPv4) ....................................... 23
Abb. 5-3: Dialog Select document type ............................................................................................ 24
Abb. 5-4: Dialog Program Settings, Optionen für Default document type ..................................... 24
Abb. 5-5: Dialog Select document type ............................................................................................ 25
Abb. 5-6: Fenster Config1.a2l - Tree view........................................................................................ 25
Abb. 5-7: Fenster Config1.a2l - Tree view, Kontextmenü ................................................................ 25
Abb. 5-8: Dialog Select device type .................................................................................................. 26
Abb. 5-9: Dialog Select device type, Pulldown-Menü geöffnet ......................................................... 26
Abb. 5-10: Dialog zur Modulkonfiguration, Fenster Config1.a2l - Tree view im Hintergrund ............. 26
Abb. 5-11: Programmfenster xx-Scan Config ........................................................................................ 27
Abb. 5-12: Menü Options | Interface ................................................................................................... 27
Abb. 5-13: Dialog Interface ................................................................................................................... 28
Abb. 5-14: Fenster Config1.a2l - Tree view ........................................................................................ 28
Abb. 5-15: Dialog XCP Gateway Configuration, Registerkarte Configuration ................................. 29
Abb. 5-16: Dialog XCP-Gateway, Registerkarte Licensing ................................................................. 29
Abb. 5-17: Dialog Select document type ............................................................................................ 30
Abb. 5-18: Fenster Config1.a2l - Tree view ........................................................................................ 30
Abb. 5-19: Menü File | Scan Bus ......................................................................................................... 31
Abb. 5-20: Fenster Config1.a2l - Tree view: erkannte Messmodule ................................................... 31
Abb. 5-21: Menü File | Auto-Configuration ......................................................................................... 32
Abb. 5-22: Auto-Configuration: "Scanning for devices..." ..................................................................... 32
Abb. 5-23: Auto-Configuration: Anzeige Resultat ................................................................................. 33
Abb. 5-24: Meldung: "Auto-Configuration ausgeführt" .......................................................................... 33
Abb. 5-25: Fenster Config1.a2l - Tree view ........................................................................................ 34
Abb. 5-26: Fenster Config1.a2l - Tree view, Kanalliste geöffnet ........................................................ 34
Abb. 5-27: Dialog für Messkanalkonfiguration....................................................................................... 34
Abb. 5-28: Eingabefeld Measurement Range: Anz. Minimal- und Maximalwert ................................. 35
Abb. 5-29: Fehler Messkanal-Konfiguration .......................................................................................... 36
Abb. 5-30: Messkanal-Konfiguration: Statuszeile mit Fehlermeldung .................................................. 36
Abb. 5-31: Dialog Bridge Balancing, Tabelle Measurement .............................................................. 36
Abb. 5-32: Dialog Bridge Balancing, Statusmeldung "AutoScale Finish" ........................................... 37
Abb. 5-33: Pulldown-Menü DMS-Werkstoff ........................................................................................... 38
Abb. 5-34: Fenster Config1.a2l - Tree view ........................................................................................ 39
Abb. 5-35: Dialog für Messmodul-Konfiguration ................................................................................... 39
Abb. 5-36: Sicherheitsabfrage "Bisherige Konfiguration überschreiben?" ............................................ 40
Abb. 5-37: Fenster Measurement Values ............................................................................................ 41
Abb. 5-38: Menü Options | Settings .................................................................................................... 41
Version 01.10
0
67 Bedienungsanleitung