Werbung
Verfügbare Sprachen
Verfügbare Sprachen
iso45-3_Holz_Textteil 31.05.13 13:48 Seite 5
GB
Check wearing parts (springs, wire cables etc) and replace
with OEM parts if necessary.
Check spring tension. Adjust spring tension as described in
the installation instructions.
Replace torsion springs and wire cables after approx.
25,000 duty cycles.
This is necessary for:
0 - 5
duty cycles per day after
6 - 10
11 - 20
Spring rapture: [3.05].
1
Slowly close door leaf. (The detent pawl snaps into the
cogs of the locking wheel and hinders the slumping of
the garage door.)
2
Secure door leaf in open position with a screw clamp
.
[
]
3.10ca
3
Press detent pawl 1 in the direction indicated by the
arrow and turn spring fixed head 2 in the direction
indicated by the arrow so that the detent pawl releases
the locking wheel.
4
Fix spring fixed heat with spring pin 97 to sole plate.
Spring pin should be in the upper perforation in the
angle frame.
[
3.10cc
5
Close door leaf carefully.
6
Carefully release the tension on functioning spring
Warning: When loosening springs wear suitable
protection and have secure footing!
7
Replace
torsion
installation instructions) and activate shearing pin.
8
Check door and replace any defective or worn parts.
5 resp. 10-year manufacturer's guarantee on
sectional doors
In addition to the warranty based on our conditions of sale and
delivery, we guarantee the aforementioned sectional doors for
10 years subject to no more than 50,000 cycles of operation.
We grant a manufacturer's guarantee of 5 years on wearing
parts, such as locks, hinges, springs, bearings, rails, rope pulls
and associated ropes subject to normal load exposure or no
more than 25,000 cycles of operation.
We grant a manufacturer's guarantee of 10 years against the
sections rusting from the inside out, on the separation of steel
from foam, and on all floor, intermediate, side and header seals.
In the case of doors with extension springs, the multiple spring
sets and double steel ropes must be replaced after approx.
25,000 cycles, while the 35R/35L torsion spring must be
completely replaced on doors with torsion springs (see
installation instructions).
If material or manufacturing faults have demonstrably rendered
the doors or parts of them unfit for use or have considerably
impaired their usability, we shall, at our own discretion, repair or
replace them free of charge.
No liability is accepted for damages caused by faulty or
improper installation, commissioning or operation, failure to
perform the specified maintenance, exposure to undue loads or
any unauthorized changes to the structure of the door. Original
spare parts only must be used when adding to, or modifying the
doors or when replacing parts in the course of maintenance or
repair works. The same applies to any damage caused during
transportation, by force majeure, foreign objects, natural wear
and tear, or atmospheric influences.
The instructions for installation, operating and maintenance must be kept in a safe place as long as the door is in use!
14 years
"
"
7 years
"
"
3.5 years
.
[
]
3.10b
.
[
]
3.10cb
.
]
.
[
]
3.10d
/
spring
35
35
completely
R
L
The warranty also lapses in the event of failure to observe our
installation and operating instructions.
No liability is accepted if functional parts are modified or
repaired without authorization or additional filling weight is added
which is not compensated by the prescribed torsion springs.
The surface warranty for all door leaves with final coating in
original colour that are installed in Germany extends to the
adhesion of the colour and/or foil, corrosion protection, and fade
resistance. Slight changes in colour that can occur over time are
excluded from the warranty. Doors and door surfaces in coastal
areas are subject to aggressive climate influences and require
appropriate additional protection. Any and all flaws or defects
arising as a result of damage to the product, such as abrasion,
mechanical or wilful damage, soiling and improper cleaning, are
excluded from this warranty.
In the case of base coated doors, the top coat must be applied
on site within three months from the date of delivery. Small
surface flaws, minor corrosion, dust inclusions or surface
scratches on base coated doors do not constitute grounds for
complaint since they will disappear once the surface is sanded
and the top coat applied.
Exposure to direct sunlight may cause doors with a width of
about 3 metres or more or with a dark paint or foil surface to
bend, and functionality may be impaired.
Our products are subject to technical alterations in the course of
product modifications, changes in colours or materials, or
improvements to production processes, which may alter their
(cf.
appearance;
such
acceptable when replacing parts under warranty.
Any faults must be communicated to us in writing immediately,
and the parts concerned must be sent to us upon request. We
will not bear any costs of removal, installation, freight or
postage. In the event that a complaint ultimately proves to be
unjustified, we reserve the right to charge the costs incurred.
This guarantee is only valid together with the signed invoice and
starts on the day of delivery.
- 5 -
alterations
are
deemed
conditionally
Werbung
