Symbols And Signage; Reference Standards; Description And Features; Power Value Accuracy - Elite Rivo Anleitung

Do not select training modes that are either too extreme or
incompatible with the health, age and physical prowess of
the user.
Setting parameters must be overseen by an experienced and
responsible adult.
Even though the product simulates road-like conditions, make
sure your posture on the bicycle is proper and comfortable.
Should you experience any discomfort or pain while working
out, stop using the home trainer right away and consult your
physician.

SYMBOLS AND SIGNAGE

On the manual and/or in some cases on the product and/or
its packaging some symbols or panels are used to highlight
or indicated dangers, obligations, warnings or notes.
Symbol Description
General warning. It prohibits from conduc-
ting said operation or maneuver
General danger: Dangerous operations or
situations, where the users or maintainers
must be extra careful.
Obligation to read: Instructions must
always be at hand and must not be dama-
ged in any way.
Notes: It indicates particularly sensitive ne-
cessary instructions.

REFERENCE STANDARDS

International standards and National laws respected in the
design and construction of the product, as well as safety and
environmental standards for use of the product.
Radio Equipment Directive (RED): Directive 2014/53/EU
RoHS Directive: Directive 2011/65/EU + Directive 2015/863
European Ecodesign Directive: Directive 2009/125/EC + EC
Regulation No. 278/2009
ETSI EN 301 489-1 V2.2.3 / ETSI EN 301 489-3 V2.3.2 /
ETSI EN 301 489-17 V3.2.4 / ETSI EN 300 328 V2.2.2
EN IEC 55014-1:2021
EN IEC 61000-3-2:2019 + A1:2021
EN 61000-3-3:2013 + A1:2019 + A2:2021 + A2/AC:2022
EN IEC 55014-2:2021
EN IEC 62311:2020
IEC 60335-1:2020
This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions:
(1) This device must not cause harmful interference and
(2) This device must accept any interference received, inclu-
ding interference that could cause undesired operation.
This device has been tested and found to comply with the
limits for Class B digital devices, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal-
lation.

DESCRIPTION AND FEATURES

The characteristics that distinguish the product are:
the wide range of powers that can be delivered during trai-
ning, the extreme roundness of pedalling and the compatibi-
lity with open communication standards.
The pedalling resistance is generated by a unit that genera-
tes a braking torque with magnetic technology, which ensures
maximum quiet operation during training.

Power value accuracy

Power data sent by home trainer is the result of multiple
calculations. These calculations take into account pedalling
speed, hometrainer brake and other factors.
Elite calibrates every single home trainer in order to improve
accuracy and reduce any margin of error, though some factors
might change over time and thus decrease power accuracy.
Spindown is a hometrainer calibration procedure that evaluates
changes arising from prolonged use and compensates their
influence on the resistance generated by the hometrainer.
Procedure:
It's important to conduct the calibration when the hometrainer
has been working for at least 10 minutes.
To conduct the procedure, select the related command on the
app or My E-Training software and follow the instructions.
The procedure start command can be found inside the settings
page of the app.
The procedure requires to start pedalling and increase speed up
to a pre-determined value.
Stop right away once you're notified to stop pedalling.
After a few seconds the procedure will notify that the calibration
procedure has been successfully completed.
The spindown value is then memorized in the Home trainer so
the correct power data is always sent to every connected device,
including non-Elite third parties software / apps / devices.
Note:
-The previous calibration procedure can also be conducted with
software / apps / devices other than Elite's.
- Do not lift your feet from the pedal until the procedure is
complete.
- The aforementioned notes are no longer valid if the hometrainer
connects to your bike's ergometer (if available) as power is no
longer calculated but measured by the sensor on the bicycle.
Please read the "Power Meter Link (PML)" chapter for further info.
Learn more about performing calibration at support.elite-it.com
EN
19