Name And List Of Components; Attention; Assembling The Drivo - Elite Drivo Handbuch

EN
N°1 Drivo body
N°2 Freehub body spacer
N°1 Chainstay adapter
N°1 Power pack
N°1 Chainstay L right spacer=142 mm (5,6 inches)
N°1 Chainstay L left spacer=142 mm (5,6 inch)
N°1 Chainstay L left adapter=130-135 mm (5,1-5.3 inch)
N°2 Feets
N°1 Quick release
CD-ROM
DVD ROM

ATTENTION!

Drivo is equipped with a freehub body compati-
ble with 9/10/11-speed cassettes by Shimano
SRAM or by other manufacturers that use the
®
Shimano® Standard.
An accessory freehub body compatible with
Campagnolo 9/10/11 speed cassettes is avai-
®
lable to replace the original Shimano compatible
body provided on Drivo; body replacement in-
structions can be found on page 26.
Drivo is compatible with 130 or 135 mm hubs and
5mm diameter quick-release.
If you are unsure about the type of derailleur on
your bicycle, refer to the bicycle documentation
or contact your dealer to ensure compatibility
with Drivo.

ASSEMBLING THE DRIVO

• Disassemble the Drivo body (Rif. A)
• Place the Drivo body (Rif. A) vertically as indi-
cated (Pic.1) and hold it in place with the upper
handle
• Rotate the foot tube 90° and place it in the pro-
per bracket welded to the leg (Pic. 1 and Pic. 2).
• Tighten the safety knob (Pic. 3).
• Spread the leg until you can hear the safety le-
ver click (Pic.4 and Pic. 5).
• (Pic. 6) shows the installation of feet (Rif. H) on
the Drivo foot tube (Rif.A).
INSTALLING THE SPROCKET
CASSETTE ON THE DRIVO
FOR M5 L=130 mm and L=135 mm
CHAINSTAYS
24

NAME AND LIST OF COMPONENTS

Your Drivo electronic trainer is made of the following components:
• Assemble the sprocket cassette on the freehub
by aligning the groove profiles.
• In order to use a Shimano
sette, or others that employ the Shimano
/
®
dard, you need to place the spacer (Rif. B) on the
freehub before inserting the sprocket cassette
(Pic. 7).
• If are installing a 9/10-speed cassette by Shi-
mano® / SRAM or by other manufacturers that
®
use the Shimano
®
(Rif. B) onto the freehub body before fitting the
cassette (Pic. 8).
• Using the torque wrench, tighten the lock ring
supplied with the cassettes onto the freehub
body (Pic. 10).
CAUTION!
Strictly follow the instructions provided by the
cassette manufacturer with regard to specific
installation techniques, the need for additional
spacers and torque specifications.
NOTE: please contact your dealer if you have
questions or are unable to install the cassette.
The warranty does not cover any DAMAGE to the
bicycle and/or Drivo in the event of incorrect in-
stallation.
• Drivo includes the correct 5mm diameter quick
release adapter for dropout spacing ranging from
130mm (5,1 inches) to 135mm (5,3 inches). There-
fore, on bikes with 130-135mm (5,1 to 5,3 inches)
dropout spacing, insert the left dropout adapter
(Ref. G) (Pic. 10). Please consult the paragraph on
page 25 for bikes with 12mm diameter (0.47 in.) x
and 142mm (5,6 in.) thru-axle spacing.
• Place the bicycle chain onto the smallest spro-
cket of Drivo (Pic 12).
(Rif. A)
(Rif. B)
(Rif. C)
(Rif. D)
(Rif. E)
(Rif. F)
(Rif. G)
(Rif. H)
(Rif. I)
/ SRAM ® 9/10 cas-
®
®
Standard, place the spacers
stan-