Transportation And Packaging; Transportation And Handling; Installation; Training Roller Assembly - Elite Rivo Anleitung

trainer, for which the user is exclusively re-
sponsible.

TRANSPORTATION AND PACKAGING

Transportation and handling

The product comes tightly packed so it's protected from
shocks and weather, nevertheless it must be carefully tran-
sported and raised by one or more users based on its weight.
The first thing to do once you open the packaging is a general
check of all the product parts; make sure all components are
accounted for and in perfect condition.
EN
22
Please remember that all packaging elements
(carton, cellophane, staples, adhesive tape
etc.) may injure you if mishandled. They must
be properly removed and not left unattended,
available to those who can't manage them; the
same goes for the tools used to remove packa-
ging, installation or maintenance (scissors,
screwdrivers, pliers etc).
It is advisable to keep the packaging in order to ensure the
protection of the product during any subsequent transport.
If the product must be shipped for service or other reasons,
proper packaging is essential:
• disconnect the power cable;
• store the product in its original packaging, if possible,
otherwise make sure to use proper packaging.
When shipped, boxes are often subject to shocks and mistre-
atment, so if packaging isn't sturdy enough (ie. non-original
packaging) it might irreparabely damage the home trainer.
Such damages are not covered by the warranty conditions.
Before sending the home trainer or any of its
components to customer service please con-
sult the Manufacturer or your local retailer.
Any non-planned shipments might be refused.

Training roller assembly

• Unpack training roller A.
• Rest training roller A horizontally.
• Fix leg bracket U and central leg S with 2 screws M8x55 V
with tightening force 20 N/m (fig. 2)
• Insert side legs T (fig. 3).
• Screw the V screws until achieving friction of the side legs
allowing them to rotate (fig. 4).
• Open the side legs to the maximum (fig. 5).
• Tighten the safety handwheels (fig. 6a).
• Adjust the stability of the training roller by screwing or un-
screwing the adjustable feet (fig. 6b).
• Warning! The side legs (Ref. T) must be able to open and
close easily.

Freehub body compatiblity

The product is supplied by the Manufacturer with a preinstal-
led freehub body compatible with the following transmissions:

INSTALLATION

Speed bicycle transmission Compatibility
Shimano / SRAM
®
9
Campagnolo
®
Shimano / SRAM
®
10
Campagnolo
®
Shimano / SRAM
®
11
Campagnolo
®
Shimano / SRAM
®
Campagnolo
®
12
Shimano Micro Spline
®
MTB
SRAM XD/XDR
®
Chain stay compatibility (pic. 2)
The home trainer is compatible with bicycles featuring a rear
chain stay with the following measurements:
Type of fastening chain stay mea-
surement (f.2)
130 mm
135 mm
Quick release
141 mm
Ø 5 mm
135 mm
Thru-axle
Ø 10 mm
135 mm
142 mm
Thru-axle
148 mm
Ø 12 mm
157 mm
Freehub body replacement (Pic. 9)
If on your bicycle you must use a different freehub body than
the one provided, replace it with a compatible one among
those indicated by the Manufacturer:
• Untighten the fixing nut R with a 17mm wrench.
• Remove the freehub body Q from the home trainer axle.
• Insert completely the new compatible freehub on the axle.
• Tighten the fixing nut R with the 17mm wrench with a 5Nm
(44in-lbs) tightening torque.
Do not attempt to adapt or use non-compatible
cassettes with the preinstalled freehub body!
®
optional - cod. 1014233
®
optional - cod. 1014233
®
optional - cod. 1014233
®
optional - cod. 1014233
optional - cod. 1014315
optional - cod. 1014279
Compatibility
optional
cod. 1014330
optional
cod. 1014306
optional
cod. 1014306
optional
cod. 1014303
optional
cod. 1014346