Werbung
Verfügbare Sprachen
Verfügbare Sprachen
PROBLEM
1. Machine requires too
much power
2. Chopper feeds irregu-
larly
3. Chopped product con-
tains a lot of long
leaves
4. Chute plugged
5. feed unit stopped
whereas the chopping
wheel continues rotat-
ing
6. Rupture of pto drive
shaft
7. Excessive wear at feed
unit input claw coupling
8. Adjustment of chopping
clearance impossible or
difficult
9. Grinding stone vibrates
G9905NT3
XI. TROUBLE SHOOTING TABLE
PROBABLE CAUSE
A. knives not sharp:
B. counter knife worn:
C. chopping clearance not cor-
rect:
D. dirt behind smooth roller:
E. V.belts slip:
. . . . . . . . .
A. entangled, lodged maize:
B. exceptionally dry and slippery
maize: . . . . . . . . . . . . .
C. adjustment of guidance tip
not correct:
. . . . . . . . .
D. cut-off discs not adjusted or
. . . . . . . . . . . .
worn:
A. chopping clearance not cor-
rect:
B. chopping knives and/or
counter knife not sharp or
worn: . . . . . . . . . . . . . .
C. counter knife needs adjust-
ment: . . . . . . . . . . . . . .
A. speed of pto too low:
B. chute touches chopped pro-
duct in wagon:
. . . . . . .
C. V-belts slip:
. . . . . . . . .
D. too much long leaves in
chopped product:
E. obstacle in chute:
Shear bolt cut :
. . . . . . . . . .
A. incorrect length:
B. insufficient lubrication (protec-
tion tubes as well!):
C. too wide an angle: . . . . .
A. lubrication insufficient:
B. incorrect alignment:
corrosion due to insufficient lubri-
cation of main drive shaft:
too much play on the guide:
table 2
EN14
. . . . .
- sharpen knives and adjust chop-
ping clearance (see IX.3.).
. . . .
- renew counter knife (see X.1.).
- correct chopping clearance (see
IX.3.B.).
- check setting of scraper; renew
scraper if required (see X.1.).
- tension belts (see IX.4.)
- install gathering combs (X.7.).
- install gathering combs(X.7.).
- adjust or renew guidance tip (see
X.3.).
- adjust or renew cut-off discs (see
X.2.).
- correct chopping clearance (see
IX.3.B.).
- sharpen knives and/or renew
counter knife (see IX.3. and X.1.).
- adjust counter knife (see X.1.).
. . .
- ensure pto speed is maintained at
1000 rpm (manual throttle control!).
- maintain sufficient distance.
- tension belts (see IX.4.).
- check chopping clearance, then
. . . . .
check condition of chopping knives
and counter knife; correct or renew
(see IX.3. and X.1.).
. . . . .
- remove obstacle.
1) fit new shear bolt (see IX.2.).
2) remove cause of blockage.
3) Check for dirt behind smooth
roller; clean as necessary.
4) check scraper setting (see
X.1.B.)
. . . . . .
- correct length.
- thoroughly grease in acc. with lu-
. . . .
brication diagram.
- do not lift too high .
. .
- ensure foam rubber in coupling
dog is always soaked with grease
(see IX.6.A.).
. . .
- contact your dealer.
Lubricate thoroughly; if no result,
. . .
contact your dealer.
.
1) tighten bolts.
2). contact your dealer
REMEDY
Werbung
