KIKKA BOO I-PRIME Gebrauchsanweisung Seite 6

IMPORTANT! KEEP FOR FUTURE REFERENCE!
EN
READ CAREFULLY!
I. PARTS
1. Headrest; 2. Shoulder pad; 3. Shoulder strap; 4. Harness buckle; 5. Baby insert; 6. Harness release button; 7. Harness strap; 8. Lap belt guide; 9. Sun shade cover; 10. Seat shell; 11.
Handle adjuster; 12. Diagonal belt guide; 13. Headrest adjuster; 14. Handle;
II. SECURING THE CHILD
Securing your baby using the baby insert
The baby insert gives your baby the necessary support while he or she is still small. The baby insert is used to provide extra comfort for very small babies.
CAUTION!
Please use the baby insert attached to this infant carrier when your baby's height is less than 75cm.
•
Always secure your baby in the infant carrier using the harness.
•
Never leave your baby unattended in the infant carrier when placing it on elevated surfaces (e.g. a table, nappy changing unit, etc.).
•
Never allow the strap end to become caught in moving parts (e.g. automatic doors, escalators, etc).
•
The plastic parts of the infant carrier heat up in the sun, be aware that your baby may get burnt. Protect your baby and the infant carrier against intensive solar radiation (e.g.
by putting a light cloth over the seat).
•
The infant carrier requires only one seating position in the car. This advantage means, however, that your baby must be in a semi-reclined position.
•
Take your baby out of the infant carrier as often as possible to relieve its spine. We recommend frequent breaks during long journeys. Even outside of the car, please avoid
leaving your baby in the infant carrier for too long.
2.1 Adjusting the handle
You can engage the handle in four positions. Simultaneously press both buttons on the handle. Then whilst holding the adjuster pressed turn the handle backwards until it engages in
the desired position.
A: Only use for carrying, can not be in this position when installing in
the vehicle seat. Caution! Ensure that the handle is securely engaged
before you pick up the infant carrier.
B: For placing your baby into the infant carrier.
C: For setting the infant carrier down safety outside the car.
D: Should be used when installed on the vehicle seat.
2.2-2.3 Adjusting the headrest
A correctly adjusted headrest ensures your baby's optimal posture in the infant carrier. The headrest must be adjusted so that the shoulder straps are at the same level as your baby's
shoulders or slightly above.
To adjust the height of the headrest to fit your baby:
Tilt the headrest adjuster until it disengages.
Slide the headrest adjuster until the shoulder straps are at the correct height and re-engage.
2.4 Loosening the shoulder straps
Press the harness release button and at the same time pull both shoulder straps forward.
2.5-2.8 Securing your baby using the harness
•
Loosen the shoulder straps.
•
Open the harness buckle (press the red release button).
•
Place your baby into the infant carrier.
•
Put the shoulder straps over the shoulders of your baby, then put the buckle tongues together and engage in the harness buckle with an audible "click".
CAUTION!
Do not twist or interchange the shoulder straps.
2.9 Tightening the harness
Pull the strap end.
CAUTION!
Pull the strap end straight towards you, not upwards or downwards.
Please pay attention to the strap end whilst travelling (especially outside the car) it should always be attached to the cover.
2.10 Checklist to ensure that your baby is buckle up correctly.
•
For the safety of your baby, please check that...
•
The shoulder straps of the infant carrier are comfortable but are a FIRM fit around your child.
•
The shoulder straps are adjusted correctly.
•
The shoulder straps are not twisted.
•
The buckle tongues are engaged in the harness buckle.
III. INSTALLATION IN THE VEHICLE
3.1-3.2 To secure the infant carrier using the 3-point belt of your vehicle proceed as follows:
•
Place the infant carrier rearward facing on the vehiucle seat (baby is facing backwards).
•
In certain cases it is possible that the infant carrier does not rest securely or is inclined too steeply on the vehicle seat.
•
Ensure that the handle is in its upper position D.
•
Pull out the vehicle seat belt and place it across the infant carrier.
•
Engage the buckle toungue in the vehicle seat buckle.
•
Place the lap belt section in the green belt guides on both sides of the infant carrier.
•
Tighten the lap belt section by pulling the diagonal belt section.
ENGLISH
IMPORTANT! KEEP FOR FUTURE REFERENCE!
EN
READ CAREFULLY!
•
Pull the diagonal seat belt section behind the top end of the infant carrier.
CAUTION!
Do not twist the belt.
3.3 For the safety of your baby, please check that:
•
The infant carrier is installed rearward facing.
•
The infant carrier is only installed on the front passenger seat if no front airbag can strike the infant carrier.
•
The infant carrier is only secured using a 3-point belt.
•
The lap belt section runs through both green belt guides on the infant carrier.
•
The diagonal belt section runs through the light green belt guides on the infant carrier.
•
The vehicle seat belt is tightened up and not twisted.
3.4-3.5 Fitting the sunshade.
Pull the head plate to expand/Fold the canopy.
IV. PRODUCT CARE
Follow these instructions for protective product care:
•
In an accident at a collision speed above 10 km/h the child safety seat could suffer damage which is not necessarily obvious. In such cases it is extremely important that you
replace the child seat. Please dispose of it properly.
•
Regularly check all important parts for damage.
•
Ensure the correct operation of all mechanical components.
•
To prevent damage or breakage, ensure that the child seat does not become jammed in the car door, seat runners, etc.
•
Should the child seat be damaged (for example after dropping it) it must be inspected by the manufacturer.
V. CARE FOR THE HARNESS BUCKLE
The function of the harness buckle is important for the safety of your child. Malfunctions of the harness buckle are mostly attributable to accumulations of dirt and dust.
4.1-4.6 Removing the fabrics to clean
1. Undo the button on the side part of the cover.
2. Undo button on the main cover.
3. Press the harness release button and at the same time pull both shoulder straps forward.
4. Undo the button on the main cover and the should pad.
5. Take off the fabric cover and wash it.
REFITTING THE FABRIC COVER
To refit the cover on the seat just hook up the elastic loops to the hooks and fit back the headrest cover.
CAUTION!
The child seat must not be used without the seat cover.
VI. CLEANING
•
The cover can be removed and hand washed at 30°C with a mild detergent. Please observe the instructions on the washing label of the cover. The colours of the cover may fade
if washed at more than 30°C. Never tumble dry in an electric clothes dryer (the fabric may separate from the padding).
•
The plastic parts can be cleaned using soapy water. Do not use harsh cleaning agents (such as solvents).
•
The harness can be removed and washed in lukewarm soapy water.
CAUTION!
Never remove the buckle tongues from the straps.
ENGLISH