IFM Electronic ecomat 100 CR2530 Original-Programmierhandbuch Seite 275

ifm Programmierhandbuch ecomatmobile
Anhang
Index S-Idx Parameter name
0x1 Short circuit OUT00...OUT07
0x2023 0x0 Output – open circuit
0x1 Open circuit OUT00...OUT07
0x2024 0x0 Output – overload
0x1 Overload OUT00...OUT01
0x2025 0x0 Input analog – overcurrent
0x1 Overcurrent IN00...IN03
0x2030 0x0 Input resistor
0x1 Resistance IN04
0x2 Resistance IN05
0x2040 0x0 System supply voltage VBBS
0x1 VBBS
0x2041 0x0 Output supply voltage
0x1 VBB1
0x2 VBB2
0x2050 Device temperature
0x20F0 Node ID
0x20F1 Node ID
0x20F2 Baud rate
0x20F3 Baud rate
0x20F4 Autostart
0x6000 0x0 Binary input
Largest sub-index supported
SmartController (CR2530, CR2532) Laufzeitsystem V03.02
Data type Default
ro USINT
ro USINT
ro USINT
ro USINT
ro USINT
ro USINT
ro USINT
ro USINT
ro UINT
ro UINT
ro USINT
ro USINT
ro USINT
ro UINT
ro UINT
ro INT
rw USINT
rw USINT
rw USINT
rw USINT
rw UINT
ro USINT
275
Details
0 0 = normal channels (bit coded)
1 = short circuit
0b---- ---X = OUT00
0b---- --X- = OUT01
0b---- -X-- = OUT02
0b---- X--- = OUT03
0b---X ---- = OUT04
0b--X- ---- = OUT05
0b-X-- ---- = OUT06
0bX--- ---- = OUT07
1 Largest sub-index supported
0 0 = normal channels (bit coded)
1 = open circuit
0b---- ---X = OUT00
0b---- --X- = OUT01
0b---- -X-- = OUT02
0b---- X--- = OUT03
0b---X ---- = OUT04
0b--X- ---- = OUT05
0b-X-- ---- = OUT06
0bX--- ---- = OUT07
1 Largest sub-index supported
0 0 = normal channels (bit coded)
1 = overload
0b---- ---X = OUT00
0b---- --X- = OUT01
1 Largest sub-index supported
0 0 = normal channels (bit coded)
1 = overcurrent
0b---- ---X = IN00
0b---- --X- = IN01
0b---- -X-- = IN02
0b---- X--- = IN03
2 Largest sub-index supported
0 0...30 000 IN04 resistance [Ohms]
0 0...30 000 IN05 resistance [Ohms]
1 Largest sub-index supported
0 VBBS voltage [mV]
2 Largest sub-index supported
0 VBB1 voltage [mV]
0 VBB2 voltage [mV]
0 temperature [°C]
124 1...125 node ID
[!] value(0x20F0) != value(20F1)
124 1...125 node ID
[!] value(0x20F0) != value(20F1)
– baud rate
[!] value(0x20F2) != value(20F3)
– baud rate
[!] value(0x20F2) != value(20F3)
0 nicht benutzt
0x02 Binär-Eingänge
Größter unterstützter Sub-Index = 2
2015-03-26
Integriertes E/A-Modul: Beschreibung