Accessories; After-Sales Service And Application Service - Bosch GSN 100-34 DK Professional Originalbetriebsanleitung

OBJ_BUCH-1037-005.book Page 16 Monday, November 10, 2014 12:55 PM
16 | English
Problem
The nails are discharged very slowly and with too little pres-
sure.
The nails are driven in too deep.
The nails are not driven in deep enough.
The pneumatic tool skips nails or has a too large cycle feed.
Frequent jamming of nails in the shot duct.
The driven nails are bent.
Contrary to working with normal operating speed, the nails are
not driven in deep enough at higher operating speed.

Accessories

For more information on the complete quality accessories
program, please refer to the Internet under
www.bosch-pt.com or contact your specialist shop.

After-sales Service and Application Service

Our after-sales service responds to your questions con-
cerning maintenance and repair of your product as well as
spare parts. Exploded views and information on spare
parts can also be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer ques-
tions concerning our products and their accessories.
In all correspondence and spare parts orders, please al-
ways include the 10-digit article number given on the type
plate of the pneumatic tool.
1 609 92A 10Z | (10.11.14)
Cause
The rated pressure of the compressed-air supply is too low.
The driver blade is damaged.
The sealing ring of the piston is worn or damaged.
The buffer is worn.
The length and diameter of supply-air hose 13 do not corre-
spond with the data of this pneumatic tool.
The supply-air hose 13 is bent/creased.
The rated pressure of the compressed-air supply is too high.
The depth stop is set too deep.
The buffer is worn.
The rated pressure of the compressed-air supply is too low.
The depth stop is set too high.
The length and diameter of supply-air hose 13 do not corre-
spond with the data of this pneumatic tool.
The supply-air hose 13 is bent/creased.
The fasteners being used are not permitted.
The magazine 8 is not operating correctly.
The spring of the magazine slider is too week or defective.
The sealing ring of the piston is worn or damaged.
The fasteners being used are not permitted.
The driver blade is damaged.
The interior diameter of the supply-air hose is too low.
The compressor is not suitable for fast operating speeds.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or ar-
range the collection of a product in need of servicing or re-
pair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Corrective Measure
– Increase the compressed-air supply. 8 bar may not be
exceeded.
– Use only the lubricants recommended by Bosch.
(See "Lubricating the Pneumatic Tool", page 15)
– Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
– Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
– Use a supply-air hose with the correct dimensions.
(See "Technical Data", page 13)
– Correct the bend/crease in the supply-air hose.
– Reduce the compressed-air supply. 5 bar may not be
fallen below.
– Adjust the depth stop to the desired depth.
(See "Adjusting the Depth Stop", page 14)
– Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
– Increase the compressed-air supply. 8 bar may not be
exceeded.
– Adjust the depth stop to the desired depth.
(See "Adjusting the Depth Stop", page 14)
– Use a supply-air hose with the correct dimensions.
(See "Technical Data", page 13)
– Correct the bend/crease in the supply-air hose.
– Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble "Technical Data" may be used.
– Clean and lubricate the magazine slider 7 as required
and make sure that the magazine 8 is not dirty/soiled.
– Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
– Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
– Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble "Technical Data" may be used.
– Contact an authorised service agent for Bosch power
tools.
– Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
– Use a supply-air hose with the correct dimensions.
(See "Technical Data", page 13)
– Use a compressor that is sufficiently dimensioned for
the number of connected pneumatic tools and the oper-
ating speed.
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Bosch Power Tools