Herunterladen Inhalt Inhalt Diese Seite drucken

Setting The Time/Date; Language Settings - Moretti Forni evolution S-Serie Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 40
for a factory set period of time. When the program has completed and
the oven is again at room temperature, it is sufficient to remove the
charred residues with a brush.
Start the "Cleaning" program by selecting the CLEANING item with
the "SELECTION" keys and press "OK" to confirm. The display will
show an icon and the message "Cleaning program in progress".
If on, the chamber lighting will switch off automatically.
At the end of the program, the oven will enter STOP mode, switching
off the power supply to the heating elements and making a buzzer
sound to warn the operator that the cleaning program is complete. The
display will read "Cleaning program completed". Press "OK" to quit
and proceed to switch off the appliance ass described in 3.9.
To stop the Oven Cleaning Program in advance, press "RETURN".
NOTE:
The steam exhaust valve needs to be shut during the
cleaning program and until it is completed. At the end, it is
recommended to open the valve to allow steam to be discharged.
3.5.3
HOTKEY
The "Hotkey" function ("star" key) is a key that can be customised for
direct access to a specific function, as chosen by the user.
Open the "Hotkey" menu to view the current setting, which will be
highlighted. To assign a different function to a "Hotkey", move the
highlighting with the "SELECTION" keys to the required item and
press "OK" to confirm.
If necessary, press "RETURN" until you return to the main screen.
Pressing the "Hotkey" will directly enable the selected function.
3.5.4
SWITCH ON TIMER
This function can be used to order timed start-up of the oven, setting up
to two different on and off times for every day of the week (fig. 21).
Scroll through the list using the "SELECTION" keys to select the
following items:
-
"Enable/Disable": enables/disables the on timer
-
"Settings": To manage the on/off programmed times
Scroll through the list with the "SELECTION" keys as far as the
"Enable" and press "OK" to confirm and enable the function. If no
switch on/off times are present, the "Settings" screen will open to
enter at least one switch on/off time.
Use the "SELECTION" keys to position the cursor on the time field
for the day of the week to be programmed. The days of the week are
set out on 4 pages. The switch on times are graphically represented by
"ON" and the switch off times with "OFF". For each day of the week
that includes a switch off, it is possible to set the cleaning program to
start up automatically. Times are graphically represented as HH:MM.
The symbols //:// show that switch on/off are disabled.
Use the "+" and "-" keys to increase/reduce the selected field. In the
HH field, select the "//" symbol to disable a specific timer. Select ON in
the CLEANING field to enable the cleaning program after the
scheduled switch off. At the end of the setting process, press "OK" to
confirm. Press "RETURN" to go back to the previous screen without
confirming the changes.
When the switch on timer is enabled, the top bar contains the "On
Timer" icon (fig.17 item I), while when the oven is in STOP mode, the
status bar messages also include the next time time the oven will be
switched on, using the format "ON dd hh:mm". While the oven is
switching off, the status bar will read "OFF dd hh:mm".
The settings table needs to be completed with even just one "On" to
activate the function: the oven will switch on at the first "on"
chronologically enabled and which it encounters in from the moment it
is enabled.
NOTE:
Setting an "On" without setting a subsequent "Off"
will still be considered an active setting: the oven will turn on
automatically at the time set, and will have to be turned off
manually. In the same way, setting "Off" that does not involve a
prior "On" will also be considered an active setting and the oven
will switch off automatically at the set time, if it was manually
switched on beforehand.
At the switch on (or off) time, an intermittent buzzer will sound and the
status icon for the timer will flash to warn of imminent switch on (or
off). This switching on or off may be interrupted by pressing the STOP
(or START) keys.
WARNING!
The sound alarm serves to signal that the
equipment is about to start up and therefore, anyone within its
radius of activity for any reason must move to a safe distance or
disconnect the equipment from the power supply; the above
function and relevant risk must be made known to all those who
might be in the vicinity of the equipment for the purpose of
safeguarding them against accidents or injury.
Once the oven has started up (or has switched off) at the set time, the
"Timer" function remains operational. Therefore, if no changes are
made, one week later at the same time, the oven will start up (or shut
down) again.
NOTE:
If the operator forces an oven start-up when the timer
is switched on before the set time, then the oven will start up
normally and at the start-up time set for the timer, everything will
proceed as usual (the oven is already on and therefore no buzzer
will sound). The same thing happens if the oven is already off at the
time set for shut down.
NOTE:
If there is a power outage while the timer is engaged,
(Blackout), no important parameter will be changed and This is as
long as the power returns before the set switch on time.
NOTE:
The control unit, powered by furnace in STOP, is
equipped with an internal timer after which automatically turns off
the display. Pressing any button wakes up the controller. With
genenerale switch in position "1" and the display is off make sure
that the unit does not enter into this state before turning off the
circuit breaker. Turn on the unit by pressing any key, then proceed
as in paragraph 3.9.
3.5.5

SETTING THE TIME/DATE

To set the time and date, use the "SELECTION" keys to move into the
field to be changed. Use the "+" and" keys to increase/reduce the
selected field. Press "OK" to confirm the change. Press "RETURN" to
go back to the previous screen without confirming the changes.
The time format is HH:MM. The date format is given as DD/MM/YY.
3.5.6

LANGUAGE SETTINGS

To set the language, scroll through the list with the "SELECTION"
keys as far as the required item and press "OK" to confirm. Press
"RETURN" to go back to the previous screen without confirming the
changes.
3.5.7
°C/°F SETTING
The oven can be set to use/view temperatures in centigrade (°C) or
Fahrenheit (°F). The current setting is shown on the main screen to the
right of the measured temperature with the relevant symbol.
To change the current settings, scroll through the list with the
"SELECTION" keys to find the required item and press "OK" to
confirm. Press "RETURN" to go back to the previous screen without
confirming the changes.
3.5.8
ASSISTANCE
This menu contains information about the oven which will be needed
when requesting Assistance.
Scroll through the list on the display using the "SELECTION" keys to
select the following items.
-
"Info": shows information about Service, about the version of the
software installed and the configuration of the oven.
-
"Software upgrade": Starts the software upgrade process
WARNING!
authorised by the Manufacturer. The operation may compromise
the correct operation of the appliance.
-
"Reset": this starts the partial reset to factory settings (any
Programs stored will be maintained in the memory)
ATTENTION!
trained and authorised by the Manufacturer. This operation may
affect the correct operation of the appliance.
-
"Factory default": this starts the general default procedure for
factory settings (any other Programs present will be deleted)
WARNING!
authorised by the Manufacturer. The operation may compromise
the correct operation of the appliance.
-
"Align": starts the vertical alignment process for the graphic.
Use the "SELECTION" keys to move the corresponding graphic.
-
"Alarms": shows any ongoing errors. The "SELECTION UP" key
scrolls through the list of alarms present. The appliance status, in
case there are pending alarms, it shown on the status bar with the
corresponding status icon (fig.17 item N).
-
"Logfile": procedure for saving baking data, reserved to the
Assistance centre.
-
"Delta Power": function that allows the power at the oven opening
to be increased/reduced while maintaining the user's power
settings. This function serves to balance out the oven settings
between the front and back. Use the specific keys to make this
correction (expressed in percentages) to the ceiling and bedplate of
the oven: positive values increase the power, while negative values
will reduce it. The corrections set will be applied at the power
percentages used in SMART BAKING mode.
UK/8
Procedure reserved to trained personnel
This procedure is reserved only to persons
Procedure reserved to trained personnel

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

S100eS120eS125e

Inhaltsverzeichnis