Moretti Forni evolution S-Serie Bedienungsanleitung Seite 21

To enable the timer T1 and start the countdown, press T1. The timer
status passes from "STOP" to "PLAY" and the countdown is enabled.
Pressing T1 again sets the timer to "PAUSE", a useful function if the
baking stage requires fillings to be added during intermediate stages.
Pressing T1 again will start the countdown from the point in which it
was stopped, setting the timer back to "PLAY". Thus, until the timer
has completed its task, as indicated by the buzzer. If the timer needs to
be stopped early, returning it to the initial setting, hold down the T1
key.
The same applies when using the timer T2.
To change the settings for the baking timer, press the "MENU" key,
select BAKING TIMER with the selection keys, then press "OK" to
open the submenu.
Scroll through the list on the display using the "SELECTION" keys to
select the following items.
- "Settings": to change the set times (fig. 19a)
- "Signal duration": to change the total duration of the signal
(fig.19b). Each bar corresponds to 10 seconds. It is possible to
de-activate the buzzer by resetting the bars to zero. This timer
status is represented by an icon in the top bar to show that the
buzzer is disabled (fig.17 item M).
Scroll through the list with the "SELECTION" key to the required
item and press "OK" to confirm. Change the parameter with the "+"
and "-" keys and then confirm with the "OK" key. To return to the
previous screens, press the "RETURN" button one or more times.
To make the TIMER settings easier, it is possible to access the
SETTINGS screen directly from the main menu screen without
passing through the "MENU", by pressing and holding down the keys
T1 and T2.
To disable the TIMERS viewing mode and return to the STANDARD
view, press the "MENU" key and select the VIEW item with the
"SELECTION" keys and then press "OK" to open the submenu.
Scroll through the list on the display using the "SELECTION" keys to
select the following items.
- "Standard": to enable the standard view
- "Timers": To enable the view required for baking timer use
- "Multitimer": activates the Multitimer display (6 baking timers)
(see 3.5.9)
Scroll through the list with the "SELECTION" keys as far as the
required item and then press "OK" to confirm.
•
"ECO STAND-BY" FUNCTION
The "Stand By" function serves to keep the oven warm while reducing
power consumption; this is the ideal solution during short breaks in
cooking operations.
Energy is saved by piloting the switching on of the floor and ceiling
heating elements at factory-set levels which guarantee that the oven
does not reach an excessively low temperature.
To enable or disable the function, press the "STAND BY" key. Once
enabled, the screen will turn GREEN and a specific icon will appear to
the left of the parameters.
NOTE:
The "Stand By" function puts the appliance into a sort
of "waking sleep", and as such it must not be used for baking, as it
would result in unsatisfactory quality.
NOTE:
The function can only be enabled with the oven in
START.
•
"POWER BOOSTER" FUNCTION
The "Power Booster" function serves to use all of the available oven
power, which is ideal when working with very large and continuing
loads, where maximum appliance speed is needed.
This is possible thanks to electronic control that can use all of the
installed power, piloting the switching on of floor and ceiling, while
maintaining the values set by the user.
Press the "BOOSTER" key to enable/disable the function. Once
enabled, the screen will become ORANGE and a specific icon appears
to the left of the cooking parameters.
NOTE:
The function can only be enabled if the oven is in
START.
•
"HALF LOAD" FUNCTION
The "Half Load" function allows baking with reduced power, the ideal
solution for the stages of intermittent work, where discontinued
equipment operation is needed.
Energy savings are possible leaving the piloting of the oven's rear
heating elements unchanged and piloting the switching on of the front
heating elements at the Manufacturer's factory settings. This means that
the operator must place the product being baked in the rear half of the
baking chamber, because, as already mentioned, the front element is on
"standby" and not usable for baking.
To enable/disable the function, press "MENU", select "HALF LOAD"
with the "SELECTION" key and then press "OK". Once enabled, the
screen will turn PURPLE and a specific icon will appear to the left of
the baking parameters.
NOTE:
This function is only possible if the oven is in START.
3.2.3 PUTTING THE BAKING CHAMBER INTO SERVICE
DUAL-TEMP MODE
The DUAL-TEMP mode is the oven control mode that allows 2
temperatures to be set, one for the ceiling and the other for the floor (fig.
18).
To enable the DUAL TEMP mode if this is not already running, press
the "MENU" key, select "DUAL TEMP" with the "SELECTION" keys
(↑ and ↓) then press "OK".
In this mode it is possible to use the oven in "MANUAL" and
"PROGRAMMES" modes, recalling the execution of one of the baking
programmes stored in the memory.
To set the temperature of the ceiling and floor, use the "+" and/or "-" to
increase and/or reduce the corresponding temperature. Since the display
shows the temperature read inside the baking chamber in real time, the
first time the corresponding "+" and/or "-" key is pressed, the current
setting will be shown in red. Pressing the keys again will change the
parameter. Once the required value has been set it is not necessary to
confirm, as the parameter is received and implemented in real time.
The operation described above can also be carried out while baking is in
progress. Temperature control is electronic and uses cutting-edge P.I.D
technology: power is a delivered so that it is always proportional and
based on the actual need identified. The oven has a virtually infinite
power spectrum, with the optimum setting being chosen instant by
instant. To turn the heating elements on and thus start heating up the
baking chamber, simply press the "START" button. The same applies to
the functions described previously in 3.2.2.
NOTE:
The temperatures of the ceiling and floor are not tied
to one another as this guarantees greater flexibility for the
operator. According to set temperature range and the load, the
two temperature settings could influence one another, no longer
guaranteeing that the set temperatures will be reached and/or it
may even be possible that the set temperatures will be exceeded.
This should not be considered a problem.
3.3 "PROGRAMS" SETTING
The use of Programs allows the operator to work in "automatic" mode,
i.e., with the possibility to save and/or recall a configuration of set
parameters. Each baking programme can store up to three baking
stages. In the SMART BAKING mode, each baking stage stores 1
temperature, 1 time and 2 power percentages to memory, while in
DUALT TEMP mode, it saves 2 temperatures and 1 time. Each
programme can also be associated to a DELTA POWER configuration
(see 3.5.8) other than the one used in MANUAL mode.
The presence of a program running is shown in the "status bar", from
the name of the program itself.
To manage the Programs, open the dedicated menu. Press "MENU",
select PROGRAMS with the "SELECTION" (↑ and ↓) keys and then
"OK" to open the submenu.
Scroll through the list on the display using the "SELECTION " keys
to select the following items.
- "Recent": a list of the last programs used
- "Name search": orders the programs starting from the
selected letter
- "Insert new": starts the procedure to create a program
- "Modify": starts the procedure for editing an existing program.
- "Delete": starts the procedure to eliminate an existing program
- "USB Import": starts the procedure to import programs from a
external usb device to internal oven memory
- "USB Export": starts the procedure to copy programs from the
internal oven memory to an external USB device
•
RECENT
Function to list the last programs used. Select the required program
with the "SELECT" keys and then press "OK" to run it and start the
heating/baking stage with the parameters of the chosen program.
•
NAME SEARCH
This is the function that lists all of the programs in the memory, in
alphabetical order, starting with the letter chosen with the
"SELECTION" key and confirmed with "OK". Select the program
required with the "SELECTION" keys, followed by "OK" to run the
program. Start the heating/baking stage with the chosen program
parameters.
UK/6