Description Of Device / Spare Parts; Engine Oil; Assembly; Preparing For Startup - ATIKA MHB 80 Originalbetriebsanleitung

Description of device / spare parts

Please refer to the attached assembly and operating
instruction sheet.
Pos. Denomination
1 Gasoline Engine
2a Hoeing tool (double) – RH
2b Hoeing tool (double) – LH
3a
Hoeing tool (single) – RH
3b Hoeing tool (single) – LH
4 Protective disc
5 Protective cover – inside
6a Protective cover – LH
6b
Protective cover – RH
7 Fuel tank
8 Tank cap
9 Fuel inlet filter
10 Air filter cover
11 Air filter cpl.
12 Foam filter
13 Paper filter
14 Clutch cable – forward
15 Steering handle
16 Adjusting screw for clutch cable - forward
17
Throttle Lever
18 ON/OFF switch
19 Clutch lever – forward
20 Handle
21 Clutch lever locking pin (forward)
22
Gas cable
23 Starter cable
24 Clutch lever – reverse
25 Adjusting screw for clutch cable - reverse
26 Clutch cable – reverse
27 Securing bolt for steering handle height
adjustment
28 Console
29 Belt cover
30 Oil filling plug
31 Oil drain plug
32 Choke Lever
33
Fuel valve
34 Cranking rope handle
35 Cranking rope
36 Silencer/exhaust outlet
37 Hoeing spur
38 Castor
39 Securing clamp for transport wheel
40 Hexagon screw M8 x 100
41 Washer A10.4
42 Hexagon nut M8
43 Spring cotter pin
44 Bolt Ø 10 x 40 mm
45 Bolt Ø 10 x 45 mm
46 Seal
47 Air filter mounting plate
Pos. Denomination
48 Spark Plug
49 Spark plug connector
50 Spark plug socket spanner
51 V-belt
Order
number
52 Toothed belt
359534 53 Safety label
381836 54 Open-end wrench, size 8/10
381837 55 Open-end wrench, size 13/16
381834 56 Open-end wrench, size 13/17
381835 57 Clutch lever locking pin (reverse)
381816
381817
381815
Steering handle
359535
Secure the steering handle (15) to the console (28)
359536
using each one screw (40), washer (41) and hexagon nut
(42).
359538
359540 Do not tighten the screw. It must still be possible to
359541 move the steering handle.
381804 Insert the angled bolt (27) in the provided hole and
secure it using the spring cotter pin (43).
381803
381806
Hoeing spur
381807
381805 Insert the bolt (44) and the washer (41) in the provided hole
in the holder. Secure it using the spring cotter pin (43).
381801
Hang in the hoeing spur (37).
381808
381809
381800
The engine of the mtoro hoe is supplied without fuel and oil
381802
in it.
381811
Fuel the motor hoe as described under "Fuelling".
381812

Engine oil

381831
Use a high-grade oil (SAE 10W-30) with classification "SF"
or higher.
Together with the recommended oil no other specific
additives are needed.
Do not mix the oil with gasoline.
359549
381814
381822
381818
381821
When using SAE 30 oil at temperatures under 10°C it is
hard to start the engine and the cylinder bore may be
damaged due to insufficient lubrication.
Oil capacity: 0.6 l

Assembly

Preparing for startup

Order
number
359539
381846
381826
381830
381843
381847
381848
381849
21