Bench Mounting; Functional Description - Makita DLS110 Betriebsanleitung

Fig.3
1 Switch trigger
5 Switch (for laser line)
(For DLS111, DLS112
only)
9 Wireless activation
button
13 Guide fence (lower
fence)
17 Bevel angle scale
21 ƒ DGMXVWLQJ EROW IRU
bevel angle)
INSTALLATION
Installing the grip
Screw the threaded shaft of the grip into the turn base.
Fig.4: 1. Grip 2. 7XUQ EDVH
Installing the dust extraction hose
Connect the dust extraction hose to the tool as
illustrated.
0DNH VXUH WKDW WKH HOERZ DQG WKH VOHHYH ¿W SURSHUO\ WR
the ports of the tool.
Fig.5: 1. Dust extraction hose 2. Elbow 3. Sleeve
4. Port

Bench mounting

When the tool is shipped, the handle is locked in the
lowered position by the stopper pin. While lowering the
handle slightly, pull the stopper pin and rotate it 90°.
Fig.6: 1. Locked position 2. Unlocked position
3. Stopper pin
7KLV WRRO VKRXOG EH EROWHG ZLWK IRXU EROWV WR D OHYHO DQG
stable surface using the bolt holes provided in the tool's
EDVH 7KLV ZLOO KHOS SUHYHQW WLSSLQJ DQG SRVVLEOH LQMXU\
Fig.7: 1. Bolt
WARNING:
Ensure that the tool will not move
on the supporting surface. Movement of the miter
saw on the supporting surface while cutting may
UHVXOW LQ ORVV RI FRQWURO DQG VHULRXV SHUVRQDO LQMXU\
2 Lock-off button
6 Battery indicator
10 Wireless activation lamp
14 Guide fence (upper
fence)
18 Releasing lever (for 48°
bevel angle)
- -
21 ENGLISH
3 Hole for padlock
7 Mode indicator
11 Hose (for dust
extraction)
15 Dust bag
19 Latch lever (for bevel
angle)
- -
FUNCTIONAL
DESCRIPTION
WARNING:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking the functions on
the tool. Failure to switch off and remove the battery
FDUWULGJH PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\ IURP
accidental start-up.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
WULGJH ¿UPO\ ZKHQ LQVWDOOLQJ RU UHPRYLQJ EDWWHU\
cartridge. Failure to hold the tool and the battery
FDUWULGJH ¿UPO\ PD\ FDXVH WKHP WR VOLS RII \RXU KDQGV
and result in damage to the tool and battery cartridge
DQG D SHUVRQDO LQMXU\
Fig.8: 1. Red indicator 2. Button 3. Battery cartridge
7R UHPRYH WKH EDWWHU\ FDUWULGJH VOLGH LW IURP WKH WRRO
while sliding the button on the front of the cartridge.
7R LQVWDOO WKH EDWWHU\ FDUWULGJH DOLJQ WKH WRQJXH RQ WKH
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
LW PD\ DFFLGHQWDOO\ IDOO RXW RI WKH WRRO FDXVLQJ LQMXU\ WR
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
NOTE: 7KH WRRO GRHV QRW ZRUN ZLWK RQO\ RQH EDWWHU\
cartridge.
4 Lid (for wireless unit)
(For DLS111 only)
8 Check button
12 Stopper pin (for carriage
elevation)
16 ƒ DGMXVWLQJ EROW IRU
bevel angle)
20 Pointer (for bevel angle)
- -