Makita DLS110 Betriebsanleitung Seite 32

4.
Push the wireless activation button on the tool
EULHÀ\ 7KH ZLUHOHVV DFWLYDWLRQ ODPS ZLOO EOLQN LQ EOXH
Fig.66: 1. Wireless activation button 2. Wireless
activation lamp
5. Pull the switch trigger of the tool. Check if the
vacuum cleaner runs while the switch trigger is being
pulled.
7R VWRS WKH ZLUHOHVV DFWLYDWLRQ RI WKH YDFXXP FOHDQHU
push the wireless activation button on the tool.
Description of the wireless activation lamp status
Fig.67: 1. Wireless activation lamp
7KH ZLUHOHVV DFWLYDWLRQ ODPS VKRZV WKH VWDWXV RI WKH ZLUHOHVV DFWLYDWLRQ IXQFWLRQ 5HIHU WR WKH WDEOH EHORZ IRU WKH
meaning of the lamp status.
Status
Color
Standby Blue
7RRO Green
registration
Cancelling Red
tool
registration
Others Red
Off
Cancelling tool registration for the
vacuum cleaner
Perform the following procedure when cancelling the
tool registration for the vacuum cleaner.
1.
Install the batteries to the vacuum cleaner and the
tool.
2. Set the stand-by switch on the vacuum cleaner to
$872 
Fig.68: 1. Stand-by switch
3.
Press the wireless activation button on the vac-
XXP FOHDQHU IRU  VHFRQGV 7KH ZLUHOHVV DFWLYDWLRQ
ODPS EOLQNV LQ JUHHQ DQG WKHQ EHFRPH UHG $IWHU WKDW
press the wireless activation button on the tool in the
same way.
Wireless activation lamp
On Blinking
20 seconds Ready for the tool registration. Waiting for the registration by the
20 seconds Ready for the cancellation of the tool registration. Waiting for the
-
NOTE: 7KH ZLUHOHVV DFWLYDWLRQ ODPS RQ WKH WRRO ZLOO
stop blinking in blue when there is no operation for
2 hours. In this case, set the stand-by switch on the
YDFXXP FOHDQHU WR $872 DQG SXVK WKH ZLUHOHVV
activation button on the tool again.
NOTE: 7KH YDFXXP FOHDQHU VWDUWVVWRSV ZLWK D GHOD\
7KHUH LV D WLPH ODJ ZKHQ WKH YDFXXP FOHDQHU GHWHFWV
a switch operation of the tool.
NOTE: 7KH WUDQVPLVVLRQ GLVWDQFH RI WKH ZLUHOHVV XQLW
may vary depending on the location and surrounding
circumstances.
NOTE: When two or more tools are registered to one
vacuum cleaner, the vacuum cleaner may start run-
ning even if you don't pull the switch trigger because
an other user is using the wireless activation function.
Duration
2 hours 7KH ZLUHOHVV DFWLYDWLRQ RI WKH YDFXXP FOHDQHU LV DYDLODEOH 7KH
lamp will automatically turn off when no operation is performed
for 2 hours.
When 7KH ZLUHOHVV DFWLYDWLRQ RI WKH YDFXXP FOHDQHU LV DYDLODEOH DQG WKH
the tool is tool is running.
running.
vacuum cleaner.
2 seconds 7KH WRRO UHJLVWUDWLRQ KDV EHHQ ¿QLVKHG 7KH ZLUHOHVV DFWLYDWLRQ
lamp will start blinking in blue.
cancellation by the vacuum cleaner.
2 seconds 7KH FDQFHOODWLRQ RI WKH WRRO UHJLVWUDWLRQ KDV EHHQ ¿QLVKHG 7KH
wireless activation lamp will start blinking in blue.
3 seconds 7KH SRZHU LV VXSSOLHG WR WKH ZLUHOHVV XQLW DQG WKH ZLUHOHVV DFWLYD-
tion function is starting up.
- 7KH ZLUHOHVV DFWLYDWLRQ RI WKH YDFXXP FOHDQHU LV VWRSSHG
Fig.69: 1. Wireless activation button 2. Wireless
If the cancellation is performed successfully, the wire-
less activation lamps will light up in red for 2 seconds
and start blinking in blue.
NOTE: 7KH ZLUHOHVV DFWLYDWLRQ ODPSV ¿QLVK EOLQNLQJ LQ
red after 20 seconds elapsed. Press the wireless acti-
vation button on the tool while the wireless activation
lamp on the cleaner is blinking. If the wireless acti-
vation lamp does not blink in red, push the wireless
DFWLYDWLRQ EXWWRQ EULHÀ\ DQG KROG LW GRZQ DJDLQ
32 ENGLISH
Description
activation lamp