Parts Description - Makita DLS110 Betriebsanleitung

Important safety instructions for
wireless unit
1. Do not disassemble or tamper with the wire-
less unit.
2. Keep the wireless unit away from young chil-
dren. If accidentally swallowed, seek medical
attention immediately.
Use the wireless unit only with Makita tools.
3.
4. Do not expose the wireless unit to rain or wet
conditions.
Do not use the wireless unit in places where
5.
the temperature exceeds 50°C (122°F).
Do not operate the wireless unit in places
6.
where medical instruments, such as heart
pace makers are near by.
7. Do not operate the wireless unit in places
where automated devices are near by. If oper-
ated, automated devices may develop malfunction
or error.
The wireless unit can produce electromagnetic
8.
¿HOGV (0) EXW WKH\ DUH QRW KDUPIXO WR WKH
user.
9. The wireless unit is an accurate instrument. Be
careful not to drop or strike the wireless unit.
10. Avoid touching the terminal of the wireless
unit with bare hands or metallic materials.
Always remove the battery on the tool when
11.
installing the wireless unit.
12. When opening the lid of the slot, avoid the
place where dust and water may come into the
slot. Always keep the inlet of the slot clean.
13. Always insert the wireless unit in the correct
direction.
14. Do not press the wireless activation button
on the wireless unit too hard and/or press the
button with an object with a sharp edge.

PARTS DESCRIPTION

Fig.2
1 Slide pole
5 Holder
9 Kerf board
13 Blade guard
17 $GMXVWLQJ EROW IRU PD[L-
mum cutting capacity)
21 Releasing lever (for turn
base)
2 Stopper pin (for carriage
sliding)
6 7XUQ EDVH
10 Blade case
14 Knob (for bevel angle)
18 Stopper arm
22 Grip (for turn base)
20 ENGLISH
15. Always close the lid of the slot when
operating.
16. Do not remove the wireless unit from the slot
while the power is being supplied to the tool.
Doing so may cause a malfunction of the wireless
unit.
17. Do not remove the sticker on the wireless unit.
18. Do not put any sticker on the wireless unit.
19. Do not leave the wireless unit in a place where
static electricity or electrical noise could be
generated.
20. Do not leave the wireless unit in a place sub-
ject to high heat, such as a car sitting in the
sun.
21. Do not leave the wireless unit in a dusty or
powdery place or in a place corrosive gas
could be generated.
22. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
23. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
ner, conductive grease or the like.
24. When storing the wireless unit, keep it in the
supplied case or a static-free container.
25. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
26. Do not use the tool with the lid of the slot dam-
aged. Water, dust, and dirt come into the slot may
cause malfunction.
27. Do not pull and/or twist the lid of the slot more
than necessary. Restore the lid if it comes off
from the tool.
28. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
3 Vertical vise
7 Pointer (for miter angle)
11 $GMXVWLQJ VFUHZ IRU
laser line)
15 Hex wrench
19 Battery cartridge
- -
4 Releasing button (for
right side bevel angle)
8 Miter angle scale
12 5DQJH DGMXVWPHQW VFUHZ
(for laser line)
16 $GMXVWLQJ VFUHZ IRU
lower limit position)
20 Lock lever (for turn base)
- -