Parts Description; Installation; Functional Description - Makita DLS714 Betriebsanleitung

PARTS DESCRIPTION

►Fig.1
1 Lock-off button
AНУustТЧРăЛШltăĚПШrăЦКбТ-
5
mum cutting capacity)
9 Blade guard
13 Lock lever (for turn base)
17 Pointer (for miter angle)
►Fig.2
19 Slide pole (upper)
23 Lever (for bevel angle
КНУustЦОЧtě

INSTALLATION

ŰОЧМСăЦШuЧtТЧР
АůRІIІżŚ źЧsurОătСКtătСОătШШХăНШОsăЧШtăЦШЯОă
ШЧătСОăsuЩЩШrtТЧРăsurПКМО. Movement of the miter
saw on the supporting surface while cutting may
rОsultăТЧălШssăШПăМШЧtrШlăКЧНăsОrТШusăЩОrsШЧКlăТЧУurв.
1. Fix the base to a level and stable surface, screw-
ing with two bolts. This helps to prevent from tipping and
ЩШssТЛlОăТЧУurв.
►Fig.3: 1. Bolt
TurЧătСОăКНУustТЧРăЛШltăМlШМФаТsОăШrăМШuЧtОrМlШМФ-
2.ă
аТsОăsШătСКtăТtăМШЦОsăТЧtШăКăМШЧtКМtăаТtСătСОălШШrăsur-
face to keep the tool stable.
►Fig.4: ń.ăAНУustТЧРăЛШlt
FUNCTIONAL
DESCRIPTION
АůRІIІżŚ ůХаКвsăЛОăsurОătСКtătСОătШШХăТsă
sаТtМСОНăШППăКЧНătСОăЛКttОrвăМКrtrТНРОăТsărОЦШЯОНă
ЛОПШrОăКНУustТЧРăШrăМСОМФТЧРătСОăПuЧМtТШЧsăШЧă
tСОătШШХ. Failure to switch off and remove the battery
МКrtrТНРОăЦКвărОsultăТЧăsОrТШusăЩОrsШЧКlăТЧУurвăПrШЦă
accidental start-up.
2 Switch trigger
6 Stopper arm
10 Vertical vice
14 Grip (for turn base)
18 Turn base
20 Thumb screw (for lock-
ing upper slide pole)
24 Slide pole (lower)
3 Blade case
7 Dust bag
11 Guide fence
AНУustТЧРăЛШltăĚПШrăturЧă
15
base)
- -
21 Hex wrench
25 Thumb screw (for lock-
ing lower slide pole)
Installing or removing battery
МКrtrТНРО
CAUTION: ůХаКвsăsаТtМСăШППătСОătШШХăЛОПШrОă
ТЧstКХХТЧРăШrărОЦШЯТЧРăШПătСОăЛКttОrвăМКrtrТНРО.
CAUTION: HШХНătСОătШШХăКЧНătСОăЛКttОrвăМКr-
trТНРОăirЦХвăаСОЧăТЧstКХХТЧРăШrărОЦШЯТЧРăЛКttОrвă
МКrtrТНРО. Failure to hold the tool and the battery
МКrtrТНРОăirЦlвăЦКвăМКusОătСОЦătШăslТЩăШППăвШurăСКЧНsă
and result in damage to the tool and battery cartridge
КЧНăКăЩОrsШЧКlăТЧУurв.
►Fig.5: 1. Red indicator
cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION: ůХаКвsăТЧstКХХătСОăЛКttОrвăМКrtrТНРОă
ПuХХвăuЧtТХătСОărОНăТЧНТМКtШrăМКЧЧШtăЛОăsООЧ. If not,
ТtăЦКвăКММТНОЧtКllвăПКllăШutăШПătСОătШШlĽăМКusТЧРăТЧУurвătШă
you or someone around you.
CAUTION: DШăЧШtăТЧstКХХătСОăЛКttОrвăМКrtrТНРОă
ПШrМТЛХв. If the cartridge does not slide in easily, it is
not being inserted correctly.
NOTE: The tool does not work with only one battery
cartridge.
TШШХă/ăЛКttОrвăЩrШtОМtТШЧăsвstОЦ
The tool is equipped with a tool/battery protection
system. This system automatically cuts off power to
the motor to extend tool and battery life. The tool will
automatically stop during operation if the tool or battery
is placed under one of the following conditions. In some
conditions, the indicators light up.
AНУustТЧРăsМrОаăĚПШră
4
lower limit position)
8 Bevel scale
12 Holder
16 Kerf board
- -
22 Clamp screw (for locking
holder)
- -
2. Button 3. Battery
ENGLISH 13