Working With The Machine; Cleaning, Maintenance And Storage - Scheppach PL55Li Originalbetriebsanleitung

The two positions (0° and 45°) are set in the fac-
•
tory.
Replacing the saw blade
m ATTENTION! Remove the rechargeable bat-
tery before changing the saw blade. Wear gloves
when handling saw blades
1 Slide the switch lock (2) to the OFF position.
Press the handles (1) sufficiently far down that
2
the saw unit latches.
3 Actuate the shaft interlock (15) and turn the saw
blade (12) until it latches.
Open the flange screw with the wrench provided.
4
5 First remove the saw blade flange (13) and then
the saw blade (12).
Insert the new saw blade (12) and the saw blade
6
flange (13) again. m ATTENTION! Observe the
direction of rotation of the saw blade.
Insert the flange screw again and firmly tighten it.
7
Return the saw to its initial position by pushing
8
the switch lock (2) into the ON position.

Working with the machine

During work observe all safety instructions provided
previously, as well as the following rules:
Only guide the electrical tool against the workpiece
•
when it is switched on.
Only use the machine if it is functioning correctly.
•
If the electrical tool has fallen, check it and the saw
•
blade for damage. Have damaged parts repaired
before use. Damaged machines can lead to inju-
ries and machine instability.
Always secure the workpiece such that it cannot
•
move during processing.
Always hold the electrical tool with both hands by
•
the handles (1) during work. This reduces the risk
of injury and is a precondition for precise work.
Always slide the saw forwards, never draw it back-
•
wards towards yourself.
Avoid the saw blade cutting edge overheating by
•
working at an appropriate feed speed, and when
cutting plastics also do so to avoid the plastic melt-
ing.
Wear a mask when carrying out dust­creating
•
work.
Switching on/off
• Slide the switch lock (2) to the ON position and
press the on/off switch (10) (pressed = ON / re-
leased = OFF).
22 І GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
After the sawing process is complete, slide the
•
switch lock (2) to the right.
Sawing
1 Place the front part of the machine onto the work
piece.
Switch the machine on using the on/off switch..
2
3 Press the plunge­cut trigger (3).
Push the saw downwards to reach the sawing
4
depth.
5 Push the saw forward evenly.
After finishing the sawing cut, switch the machine
6
off and move the saw blade upwards.
Plunge-cuts, Fig. 5
Place the saw onto the work piece.
1
2 Place the cutting indicator with the rear arrow (A)
on the marked plunge­cut position.
Switch the machine on and push the saw down-
3
wards until you reach the set cutting depth.
Move the saw forwards until the cutting indication
4
(C) has reached the marked point.
After completion of the plunge­cut, move the saw
5
blade upwards and switch the saw off.
Cutting with rails (otional)
Place the machine in the guide rails. can be read-
1
justed using the hex driver included in the delivery,
when there is the risk of the adjusting screws re-
leasing by themselves.
Turn on the machine by pressing the on/off switch.
2
Press the dip trigger (3).
3
Press the saw downwards to reach the sawing
4
depth. During first use the rubber lip is sawn off
and thus splitter protection is guaranteed up to
the saw blade.
5 Push the saw uniformly forwards.
Turn off the machine and tilt the saw blade to the
6
top when the saw cutting is complete.
Sawing with dust suction
Connect the suction hose to the exhaust nozzle ­ Ø
38 mm (4).

Cleaning, maintenance and storage

m Risk of injury, electric shock
Always remove the rechargeable battery pack from
•
the electrical tool before performing maintenance
and service work!