Reference Numbers; Reference Numbers Instruments - LumaSense Technologies mpac IN 140/5-L Betriebsanleitung

IMPAC pyrometers IN 140/5 · IN 140/5-H · IN 140/5-L
Error status:
Laser targeting light:
Reading interface:
Lock keyboard:
Reading parameters:
Device type:
Serial number:
Device type /
software version:
Detailed Software
version:
Reference number:
Note: the letter "l" means the lower case letter of "L".
Additional instruction for the RS 485 interface:
Requirements to the master system during half-duplex operation:
1. After an inquiry, the bus should be switched into a transmission time of 3 bits
(some older interfaces are not fast enough for this).
2. The pyrometer's response will follow after 5 ms at latest.
3. If there is no response, there is a parity or syntax error and the inquiry has to be repeated.
15

Reference numbers

15.1

Reference numbers instruments

Type Temperature range
IN 140/5 MB 14:
IN 140/5 MB 16:
IN 140/5 MB 15:
IN 140/5 MB 25:
IN 140/5-L MB 14:
IN 140/5-L MB 16:
IN 140/5-L MB 15:
IN 140/5-L MB 25:
Ordering note:
When ordering please select one optics (1-N, 2-N or 3-N for IN 140/5 or 2-N for IN 140/5-L)
(see section 7, Optics).
A connection cable is not included in scope of delivery and has o be ordered separately.
24
AAfs Output: XX;
AAlaX
X = 0 switch off laser
X = 1 switch on laser
AAin Output: 1 or 2 (1 = RS232, 2 = RS485)
AAlkX
X = 0 ... 3
AApa Output 11-digit, decimal:
AAna Output: "IN 140/5" (16 ASCII-characters)
AAsn Output: XXXXX (dec. 5-digit)
AAve Output: XXYYZZ (6-digit decimal)
AAvs tt.mm.yy XX.YY
tt = day; mm = month; yy = year; XX.YY = software version
AAbn Output: XXXXXX (hex 6-digit)
With laser targeting light
250...1400°C
300...1600°C
450...1500°C
500...2500°C
250...1400°C
300...1600°C
450...1500°C
500...2500°C
XX=00...FF (00 = no error)
(01...FF: error code for LumaSense service)
1 = lock lk1, removal with command lk0 or power off-on
0 = removal of lock lk1
3 = continuous lock lk3, removal only with command lk2
2 = removal of lock lk3
Digit 1 und 2 (10...99 or 00=100%): Emissivity
Digit 3 (0 ... 6): Exposure time
Digit 4 (0 ... 8): Clear time max. storage
Digit 5 (0 ... 1): Analog output
Digit 6 und 7: (00 ... 98): Internal temperature
Digit 8 und 9 (00 ... 97): Address
Digit 10 (0 ... 6 or 8): Baud rate
Digit 11 (0,1, 3): Keyboard lock
XX = 60 (IN 140/5)
YY = Month of software version
ZZ = Year of software version
3 877 380
3 877 360
3 877 400
3 877 420
3 877 480
3 877 460
3 877 500
3 877 520
With thru-lens view finder
3 877 390
3 877 370
3 877 410
3 877 430
3 877 490
3 877 470
3 877 510
3 877 530