Scheppach HBS261 Originalbetriebsanleitung Seite 41

ATTENTION
According to the German Product Liability Act, no liabili-
ty is accepted for damage caused by improper repairs
or by not using original spare parts.
Such work should be performed by a customer service
centre or an authorised specialists. The same applies to
accessory parts.
Connections and repairs
Connections and repair work on the electrical equipment
may only be carried out by electricians.
16.1 Ordering spare parts
Please provide the following information when ordering
spare parts:
• Model designation
• Item number
• Type plate data
Spare parts / accessories
Band saw blade - Article no.:
Table inlay - Article no.:
16.2 Service information
With this product, it is necessary to note that the following
parts are subject to natural or usage-related wear, or that
the following parts are required as consumables.
Wearing parts*: Band saw blade, table inlay, belt
* = may not be included in the scope of delivery!
17 Disposal and recycling
Notes for packaging
The packaging materials are recy-
clable. Please dispose of packag-
ing in an environmentally friendly
manner.
Notes on the electrical and electronic equipment act
(ElektroG)
Waste electrical and electronic equipment
does not belong in household waste, but must
be collected and disposed of separately!
18 Troubleshooting
Fault
Motor does not work
The engine runs slowly and does
not reach the operating speed.
Engine producing excessive noise. Coils damaged, motor defective. Arrange for inspection of the motor by a specialist.
The engine does not reach full
power.
Motor overheats easily.
7901505702
5901514013
Possible cause
Motor, cable or plug defective,
mains fuses blown,
both safety switches are not cor-
rectly engaged.
Voltage too low, coils damaged,
capacitor burnt.
Circuits in the network are over-
loaded (lamps, other motors,
etc.).
Overloading of the motor, insuffi-
cient cooling of the motor.
www.scheppach.com
• Used batteries or rechargeable batteries that are not
installed permanently in the old device must be re-
moved non-destructively before disposal! Their dis-
posal is regulated by the battery act.
• Owners or users of electrical and electronic devices
are legally obliged to return them after use.
• The end user is responsible for deleting their personal
data from the old device being disposed of!
• The symbol of the crossed-out dustbin means that
waste electrical and electronic equipment must not be
disposed of with household waste.
• Waste electrical and electronic equipment can be
handed in free of charge at the following places:
– Public disposal or collection points (e.g. municipal
works yards)
– Points of sale of electrical appliances (stationary
and online), provided that dealers are obliged to
take them back or offer to do so voluntarily.
– Up to three waste electrical devices per type of de-
vice, with an edge length of no more than 25 centi-
metres, can be returned free of charge to the man-
ufacturer without prior purchase of a new device
from the manufacturer or taken to another autho-
rised collection point in your vicinity.
– Further supplementary take-back conditions of the
manufacturers and distributors can be obtained
from the respective customer service.
• If the manufacturer delivers a new electrical device to
a private household, the manufacturer can arrange for
the free collection of the old electrical device upon re-
quest from the end user. Please contact the manufac-
turer's customer service for this.
• These statements only apply to devices installed and
sold in the countries of the European Union and which
are subject to the European Directive 2012/19/EU. In
countries outside the European Union, different regu-
lations may apply to the disposal of waste electrical
and electronic equipment.
Remedy
Arrange for inspection of the product by a special-
ist. Never repair the motor yourself. Danger!
Check mains fuses, replace if necessary, engage
both safety switches correctly
Have an electrician check the voltage. Arrange for
inspection of the motor by a specialist. Arrange for
replacement of the capacitor by a specialist.
Do not use any other products or motors on the
same circuit.
Avoid overloading the motor while cutting, remove
dust from the motor in order to ensure optimal
cooling of the motor.
GB | 41