German RepRap PRotos V2.0 Handbuch Seite 12

PRotos V2.0 3D Drucker Handbuch
3.47. Materialliste Befestigung Heizmatte ..................................................................................... 164
3.48. Materialliste Vormontage Thermistor (100013.2) ...................................................................... 164
3.49. Materialliste Isolierung Thermistor ........................................................................................ 167
3.50. Materialliste Montage Thermistor (100013.3) ........................................................................... 169
3.51. Materialliste Montage Thermistor ......................................................................................... 169
3.52. Materialliste Kabelhalterung (100013.4) .................................................................................. 171
3.53. Materialliste Kabelhalterung ............................................................................................... 171
3.54. Materialliste Dämmwatte .................................................................................................... 174
3.55. Materialliste Befestigung beheizbares Druckbett (100013.5) ....................................................... 176
3.56. Materialliste Befestigung beheizbares Druckbett .................................................................... 176
3.57. Materialliste Opferplatte ..................................................................................................... 180
3.58. Materialliste Mosfet-Kühler (100013.6) ................................................................................... 182
3.59. Materialliste Vorbereitung Pololus ........................................................................................ 184
3.60. Materialliste Montage Kühlrippen ......................................................................................... 186
3.61. Materialliste Vorbereitung Pololus ........................................................................................ 188
3.62. Materialliste Elektronikhalterung (100270.17) .......................................................................... 191
3.63. Materialliste Elektronikhalterung .......................................................................................... 191
3.64. Materialliste Ramps-Lüfter (100270.18) ................................................................................... 193
3.65. Materialliste Ramps-Lüfter ................................................................................................. 193
3.66. Materialliste Opto Endstop - X-Achse (100270.19) .................................................................... 195
3.67. Materialliste Opto Endstop - X-Achse ................................................................................... 195
3.68. Materialliste Opto Endstop - Z-Achse (100270.20) .................................................................... 198
3.69. Materialliste Opto Endstop - Z-Achse ................................................................................... 198
3.70. Materialliste Opto Endstop - Y-Achse (100270.21) .................................................................... 201
3.71. Materialliste Opto Endstop - Y-Achse ................................................................................... 201
3.72. Materialliste Verkabelung Y-Achse ........................................................................................ 204
3.73. Materialliste Verkabelung Z-Achse ........................................................................................ 206
3.74. Materialliste Verkabelung X-Achse ........................................................................................ 211
3.75. Materialliste Verkabelung Hot-End ........................................................................................ 214
3.76. Materialliste Verkabelung ATX-Buchse und Ramps .................................................................. 216
3.77. Kabelbündelung am Extruder DD .......................................................................................... 226
3.78. Anbringung des Bowden bei einem Extruder ........................................................................... 229
3.79. Materialliste LCD-Display .................................................................................................... 233
3.80. Materialliste Verkabelung Druckbett (100013.7) ....................................................................... 237
4.1. Übersicht der benötigten Programme Firmware (OS X) .............................................................. 239
4.2. Download Repetier-Host (OS X) ............................................................................................. 248
4.3. Übersicht der benötigten Programme Slic3r (OS X) .................................................................... 250
4.4. Übersicht der benötigten Programme Firmware (Windows) ........................................................ 251
4.5. Übersicht der benötigten Programme Repetier-Host (Windows) ................................................... 256
4.6. Übersicht der benötigten Programme Slic3r (Windows) .............................................................. 257
4.7. Materialliste Inbetriebnahme SD RAMPS ................................................................................. 258
© German RepRap GmbH
Seite 12 /
Revision 352
Stand 23.12.2013 14:03
PRotos V2.0 3D Drucker Handbuch
12 /