EDELRID FLEX LITE Bedienungsanleitung Seite 13

ANCHOR POINT
In order to avoid high loads and swinging falls in the
event of a fall, anchor points for belay purposes must
always be as vertical as possible above the person to
be belayed. The lanyard/ anchor device from the
anchor point to the person secured should always be
kept as taut as possible. Slack ropes must be avoid-
ed! The anchor point must be designed in such a way
that, when fixing the PPE, no effects can occur which
reduce the stability and it is not damaged during use.
Sharp edges, ridges and crushing can seriously
impair the stability. These should be covered, where
necessary, using suitable auxiliary equipment. The
anchor point and the anchoring must be able to with-
stand the expected loads in a worst-case scenario.
Even if energy absorbers (to EN 355) are used, the
anchor points must be specified for a fall arresting
force of up to 12 kN, also refer to EN 795.
When using a lanyard (fall arrest system), please note
that the maximum overall length of the lanyard in-
cluding shock absorbers and connecting compo-
nents must not exceed 2.0m.
SAFETY NOTICES
When combining this product with other compo-
nents, the safety aspects of the products may
interfere with each other.
If this product is used in combination with other
components of a rescue/fall arrest system, users
must acquaint themselves with the enclosed rec-
ommendations, notes and instructions for these
components prior to use and comply with them.
This equipment should only be used in connection
with parts of personal protective equipment (PPE)
bearing the CE-symbol to protect individuals against
falls from heights.
If original components are modified or removed from
the product, its safety aspects may be restricted. The
equipment should not be modified in any way or
altered to allow attachment of additional parts with-
out the manufacturer's written recommendation.
The equipment must be checked for possible
damage before and after each use. It must be
ensured that the equipment is serviceable and
fully functional. The equipment must be discarded
immediately if there is even the slightest doubt as
to its serviceability.
WARNING! The products must be kept away from
damaging environments. This includes contact with
abrasive and aggressive substances (e.g. acids
(battery acid!), alkalis, soldering water, oils, clean-
ing agents), as well as extreme temperatures and
flying sparks.
In addition, sharp edges, wetness and especially ic-
ing-up can diminish the stability of textiles.
CLIMATE REQUIREMENTS Fig. 10b
The permanent use temperature of the product (in
dry condition) ranges from approx. -20°C to +55°C.
LIFESPAN AND REPLACEMENT
The lifespan of the product mainly depends mainly
on the way and frequency in which it is used and
external influences.
Products made from synthetic fibre (polyamide, poly-
ester, dyneema) are subject to a certain ageing pro-
cess even if they are not used. This is caused by the
intensivity of UV-rays and environmental influences.
The maximum service life at optimum storage con-
ditions (see item Storage) and with no use is 14 years.
The maximum usage time (commercial/non-com-
mercial use) assuming proper use, no visible signs of
wear, and at optimum storage conditions is 10 years.
PPE showing signs of wear must be replaced, for in-
stance, if the edges of webbing and straps are dam-
aged, if fibres have come off the webbing, if seams
are damaged or show signs of wear, or if the equip-
ment has come in contact with chemicals. Watch out
for sharp burrs or signs of corrosion on metal parts
of the equipment. Repairs may only be performed as
outlined in the instructions of the manufacturer.
In case of extreme use (extreme signs of wear), for
instance, upon strain by a fall or when damage is vis-
ible, immediately remove the PPE from use and turn it
over to the manufacturer or a competent person for
inspection and/or repair; be sure to request a written
confirmation for the work done (Fig. 13).
Repairs may only be performed as outlined in the
instructions of the manufacturer.
INSPECTION
The product must be checked and, if necessary,
maintained whenever this is necessary but at least
yearly by the manufacturer, an expert or an autho-
rised testing centre.
In the process, it must be ensured among other
things that the product labelling is legible.
When the maximum service life of 10 years has been
reached, the PPE must be removed from further use.
STORAGE, TRANSPORT AND CARE
Storage
Store in a cool, dry, dark place outside transport
containers. Avoid contact with chemicals (caution:
battery acid!) Store without mechanical stress
caused by jamming, pressure or tension.
Transport
The product must be kept away from direct sunlight,
chemicals, dirt and mechanical damage. For this
purpose, a protective bag or special storage and
transport containers should be used.
Cleaning Fig. 10a and 11
Clean soiled products in luke-warm water (if neces-
sary, use pH-neutral soap). Rinse well. Dry at room
temperature, never use a tumble drier or dry close to
radiators! If required, halogen-free commercial disin-
fectants may be used.
If required, hinges of metal parts may be oiled after
cleaning.
WARNING! Failure to follow these instructions
may endanger life!
INFORMATION ON THE PRODUCT
Manufacturer: EDELRID
Product description:
Fall arrest harness according to EN 361,
ANSI/ASSP Z359.11
Model: Flex Lite
Size
Maximum user load
YYYY MM: Year and month of manufacture
Lot number: GV xxx xxxx
Identification: (to be entered by the user him/herself
if appropriate)
0123: certification body monitoring the PPE pro-
duction
Warning notices and instructions must be read
and observed
Fall arrest harness to EN 361: Marking A and A/2
(A/2 + A/2 = A ): catch eye
Material:
- Polyamide = PA
- Polyester = PES
- Aluminium = ALU
- Steel = Steel