Additional Assembly Options For Hand Operation; Reno" Installation Condition; Completing The Installation Procedure - Novoferm iso20-4 ZF Original-Montage- Und Betriebsanleitung

Proceed as follows to mount a guide plate (99):
Swing the guide plate (99)
frame (1L/1R) and connect it with the screw (S3).
Fig. b Close the door to make final adjustments on
the upper track rollers. Make sure that the mounting
blocks under the door leaf have been removed.
Fig. c For hand operation or NovoPort drive: Posi-
tion the centres of the track roller in a way that it is
centrally aligned with the inner edge of the tail end.
Observe that the track rollers must be positioned by
approx. 25 mm to the top when operating the system
with a ceiling pull drive.
After having adjusted the upper track roller, tighten
the screws on the roller holder (105L/105R).
Fig. d In order to complete the assembly, carefully
insert the safety guard (39) on both sides of the rails.
Fig. e Check the frame and shutter seals for any de-
formation. Their original shape can be restored with a
hot air gun or similar.
4.7 Additional assembly options for hand
operation
4.7.1 Mounting the manual cable (optional)
Risk of injury caused by
WARNING
strangulating limbs
If manual cable and door drive are both
installed in the system, there is a risk of
limbs getting caught and strangulated
by the manual cable when moving the
door.
• If the door drive is already installed
or shall be installed, the manual
cable must not be mounted!
Fig. a , page A22. Mount the cable holder (91) for
the manual cable (96) on the bottom section (44) us-
ing the screws (S10). In doing so, observe the per-
missible torque of 10 Nm.
Fig. b Feed the manual cable (96) through the re-
spective hole in the cable holder (91) and secure it
with a knot.
Fig. c Suspend the manual cable (96) on the con-
necting plate (18), also by tying a knot.
4.7.2 Mounting the rail clamps
Manually open the door and mark the end position of
the uppermost track roller (105L/105R).
Fig. a , page A22. Close the door and mount the rail
clamps (89) with the screws (S14) on the marked po-
sition.
Fig. b Note that the distances from the end of the
rails to the rearmost end of the clamp must be
identical on both sides.
4.7.3 Mounting the bolt plate
Close the door. Afterwards,
plate (93L/93R) onto the locking bolt (79) on the right
and left side and mark the positions.
These assembly, operation and maintenance instructions must be kept for the entire period of use!
Fig.
into the angle door and screw the bolt plate (93L/93R) into both re-
spective rectangular holes (front row of holes) of the
angle frame (1L/1R).
Check the locking by opening and closing the door
several times. For closing, the locking bolt (79) al-
ways
plate (93L/93R). If required, the position has to be ad-
justed by shifting the bolt plate (93L/93R) vertically.
Fig.
the bolt plate (93L/93R) and the angle frame (1L/1R)
by means of the screws (S6 + S12).
4.8
NOTICE
Fig.
frame (1L/1R), cut off the foot angle at the predeter-
mined breaking point by bending it downwards. Then
remove the free-standing flap from the angle frame.
NOTICE
Fig.
gap (wall and floor rail). Please also refer to the in-
structions in the chapter "Mounting the plugs for the
door frame".
4.9
In order to ensure proper functioning, durability and a
smooth running of the sectional door it is essential
that all parts have been mounted in accordance with
the assembly instructions. Check if the garage door
operates properly and safely. The following points are
to be checked in particular:
•
•
•
•
hold the bolt
a , page A23. Using the screws (S17), open the
has to fully engage
b Additionally mount a securing bracket (94) to

"Reno" installation condition

Observe the installation
requirements.
Fig. a , page A23. Only carry out the
following steps if you have checked the
distance between the stop and the front
rail. The distance should be at
least 60 mm.
b and Fig. c At the lower end of the angle
Potential rust formation at separation
point!
Protect the separation points against
corrosion by touching up the areas with
touch-up paint (not included in the
scope of delivery).
d Set up the door frame and insert it into the

Completing the installation procedure

Are the lateral angle frames, the frame panel and
the horizontal rail pairs exactly aligned
horizontally, vertically and diagonally, and are
they securely fastened?
Are all screw connections tight?
Are all ceiling suspensions of the horizontal rail
pairs mounted?
Have the transitions between the vertical rails in
the angular frame and the 89° arches been
adjusted?
into the bolt
EN - 25