Important Assembly Instructions; Installation Of The Tubular Motor; Mounting The Bearings (Figure  ) - RADEMACHER X-line Handbuch

Important assembly instructions

IMPORTANT
◆ Check that the voltage / frequency on the type plate corresponds to local mains
conditions prior to installation.
◆ All cables and equipment not required for operation of the equipment is to be removed
or deactivated prior to installation of the tubular motor.
◆ Moving drive parts to be operated at a height under 2.5 m from the floor must be
protected.
◆ If the tubular motor is to be controlled with a switch with a default OFF setting, then
the switch is to be positioned in the line of sight of the tubular motor and at a height
of at least 1.5 m.
◆ The cover of the roller shutter box must be freely accessible and removable.
◆ Never dismantle the stopper from the final roller shutter lamella.
Otherwise the roller shutters may slip through into the roller shutter box and be
damaged.
Assign the physical address for the tubular motor
The RolloTube X-line tubular motors are assigned an identical physical address at the
factory (see page 67). When setting up a KNX network, every KNX device must
be assigned to an individual physical address on the network.
IMPORTANT
The physical address of the X-line tubular motor must be programmed
prior to the completion of the final mounting and installation work (see
page 67, „Activating registering mode for X-line tubular motors".)

Installation of the tubular motor

NOTE
The following installation instructions apply to standard installation situations in combination
with RADEMACHER tubular motors and accessories.
The drive head (12) of the motor can be installed on either the right or left sides of
the roller shutter box. These instructions depict the installation on the right-hand side.
Mounting the bearings (Figure  )
Check that the bearing are installed horizontally. Roller shutters wound
at an angle can block the drive and cause damage.
52
CAUTION
Installing the tubular motor at an angle can cause the tubular motor or
roller shutters to be damaged. For example, roller shutters wound at
an angle can block the drive and cause damage.
◆ Always ensure that the tubular motors and bearings are mounted
horizontally.
◆ Please ensure that the rotating union (5) and the roller shutters
(18) can move down easily and freely after installation is complete.
◆ The roller shutters (18) may not run over the bearing, the bearing capsule (4) or the
drive head (12) during operation.
◆ Ensure that the rotating union (5) and the fastening springs (6) of the drive (9) do
not touch. They may not rub against the tubular motor (9) during operation.
For automatically actuated awnings:
◆ A minimum gap of 0.4 m to other parts in the area must be maintained when the
awning is fully extended.
◆ Awnings used in an awning system must maintain a minimum height of 1.8 m.
Only use tubular motors which correspond to the local conditions in
terms of their power. Incorrectly dimensioned tubular motors can lead
to damage.
◆ Incorrectly dimensioned drives and counter bearings can cause the roller shutter system
to be damaged. Only use original bearings supplied by the manufacturer. Third-party
drives and counter bearings must be selected in accordance with the torque specifica-
tions of the respective tubular motors.
Risk of injury in the event of incorrect installation (impact injuries and
contusions).
◆ The motor can eject from the drive bearing in the event of incorrect installation/
fastening. Fasten the tubular motor with the securing devices provided.
Mortal danger in the event of operation without configured end points.
◆ The end points must be configured in order to ensure safe operation. In order to do
so, please refer to the corresponding chapter in this manual provided on page 59.
Required minimum width for the roller shutter box:
Tubular motor type:
Minimum width approx.:
1. First determine the position of the drive bearing (13) and counter bearing
(1) in the roller shutter box.
Wind the roller shutter casing fully onto the rotating union and measure diameter D. See
figure  in order to determine the position of the centre of the bearing to the guide rail.
IMPORTANT
When installed, the wound roller shutter must run vertically in the guide rails on the window.
2. Fasten the bearing in accordance with the bearing type and on-site
conditions.
Mount the drive bearing (13) so that the set button (11) will be easily accessible and
the motor cable can be laid without kinking.
Medium
67 cm
EN