Inhaltsverzeichnis
Werbung
Users Instructions
Control display
Buttons:
c: Start
a head fan -
1 Starts the tanning unit in stand-alone
b head fan +
mode (also quick start at external timer
c start
or coinbox with pre-time setting).
d stop
e body fan -
d: Stop
f body fan +
1 Stops the solarium.
g middle face tanner or soft lamps
on/off
e: Body fan -
h outer face tanners or soft lamps on/off
1 Reduces the amount of air on the body
i led display
(adjustable in 5 levels).
k Xsens button and programming button
2 Displays the working hours
Maximum tanning time: 30 minutes.
(see "k").
a: Head fan -
f: Body fan +
1 Reduces the amount of air around the
1 Increases the amount of air on the body
head (adjustable in 5 levels).
(adjustable in 5 levels).
2 Reduces the stand-alone time
2 For setting the stand-alone time
(see "k").
(see "k").
b: Head fan +
g: Face
1 Reduces the amount of air around the
1 For switching the middlemost face tanner
head (adjustable in 5 levels).
and soft lamps in the face area on and
2 Reduces the stand-alone time
off.
(see "k").
h: Face/ /body
i: Led display
1 For switching the outermost face tanners
1 Control panel display.
or soft lamps in the body area on and off.
the user may switch off the face tanner
k: Xsens button
lamps while tanning. The cooling-off
Only if the tanning unit is provided with the
period of these lamps is 4 minutes. If the
Xsens accessoires.
face tanner lamps are switched off during
1 At the start of the tanning session the
tanning and the user wishes to switch
Xsens unit is switched off.
them back on again but the 4 minutes of
The Xsens unit can be switched on or off
cooling-off time have not yet passed, indi-
by means of the button.
cator lamps will light up on the led dis-
When the Xsens unit is switched on, 'on'
play, to display that the face tanners are
will flash 4 times on the display of the
activated and that you should wait until
control panel. When the Xsens unit is
the 4 minutes have elapsed:
switched off, 'off' will flash 4 times on the
* If the "face" is switched on again within
display of the control panel.
these 4 minutes, the middlemost indicator
lamp on the led display will light up.
2 Setting the STAND-ALONE time:
* If the "face/body" is switched on again
step1: keep the "xsens button" pressed
within these 4 minutes, the outermost two
while pressing: "body fan +"
indicator lamps on the led display will
step2: set the stand-alone tanning time
light up.
using:
* "head fan +" to increase the tanning
time
* "head fan -" to reduce the tanning
time
13
k
a
b
i
e
f
step3: wait for 15 seconds after setting the
tanning time
step4: next, press "start", for checking the
set up time.
note: when using an external timer or coin
box, set the stand-alone-time to
"zero".
3 Reading the number of working hours
keep the "xsens button" pressed while
pressing "body fan -".
To obtain the number of working hours,
multiply the figure on the display by 10.
After reading out the number of working
hours, wait 15 seconds.
(Point 1 and 2 only apply in case the
machine is in off-mode.)
There is a 3 minute set (required) after-
cooling time after every tanning session.
the solarium can not be switched on
during these 3 minutes.
c
d
g
h
Werbung
Inhaltsverzeichnis
