Loading The Magazine - Parkside PDT 40 E4 Bedienungs- Und Sicherheitshinweise

Proper functioning of the fastener driving tool re-
quires filtered, dry and oiled compressed air in
adequate quantities. If the air pressure in the line
system exceeds the maximum permissible opera-
ting pressure of the fastener driving tool, a pressure
reducing valve followed by a downstream safety
valve shall additionally be fitted in the supply line
to the tool.
Legende der verwendeten Piktogramme
Note: When compressed air is generated by com-
Einleitung
pressors, the natural moisture in the air condenses
........................................................................................................................................Seite 6
and collects as condensed water in pressure ves-
Bestimmungsgemäße Verwendung ...................................................................................................Seite 6
sels and pipelines. This condensate must be remo-
Ausstattung ..........................................................................................................................................Seite 6
ved by water separators. These water separators
Lieferumfang .......................................................................................................................................Seite 6
must be checked on a daily basis and drained if
Technische Daten ................................................................................................................................Seite 7
necessary, since corrosion can otherwise develop
Sicherheit
in the compressed air system and in the fastener
........................................................................................................................................Seite 7
driving tool, which serves to accelerate wear.
Allgemeine Sicherheitshinweise ........................................................................................................Seite 7
Vor der Inbetriebnahme
The compressor plant shall be adequately dimensi-
oned in terms of pressure output and performance
Gerät aufstellen ..................................................................................................................................Seite 8
(volumetric flow) for the consumption which is to
Inbetriebnahme
be expected. Line sections which are too small in
relation to the length of the line (pipes and hoses),
Heizstufen und Ventilator ein- / ausschalten .....................................................................................Seite 8
as well as overloading the compressor, will result
Temperatur einstellen..........................................................................................................................Seite 9
in pressure drops.
Gerät ausschalten ..............................................................................................................................Seite 9
Überhitzungsschutz ............................................................................................................................Seite 9
Oilers should be checked daily and, if necessary,
Fehlerbehebung
filled with the recommended oil (see technical
data). When using hose lengths over 10m, the sup-
Wartung, Reinigung und Lagerung
ply of the nailer with oil is not guaranteed. We th-
erefore recommend an lubricator attached directly
Service
to the fastener driving tool or to manually lubricate
...............................................................................................................................................Seite 10
the air inlet directly with 2 - 5 drops of the recom-
Garantie
mended grade of oil(see technical data).
...........................................................................................................................................Seite 11
Entsorgung
Use only hoses with an internal diameter not less
.....................................................................................................................................Seite 11
than 9mm. Otherwise the staples/nails will be shot
Original-EG-Konformitäts erklärung / Hersteller
out of the machine slow and with little pressure.

Loading the magazine


Only those fasteners specified under technical data
may be used. When filling the magazine, hold the
tool so that the muzzle is not pointing towards your
own body or towards any other person.
Safety / Preparing the product for use /
....................................................................................................Seite 8
........................................................................................................................Seite 8
........................................................................................................................Seite 10
1. Press the magazine lever
zine cover back to its stop position.
2. Insert the corresponding fastener (nails, see
Fig. B or staples, see Fig. C) into the magazi-
ne
. The tacks must be put on the rail of the
7
magazine .
7
3. Slide the magazine cover forwards until it locks.
.........................................................Seite 6
Use

□
Load the magazine
tacker as described in the chapter "Loading
the magazine".
□
Use the pressure reducer to set the correct ope-
rating pressure.
□
Ensure that the permissible operating pressu-
re of 8 bar at the device is never exceeded.
Operating pressure that is too high does not
provide any performance increase, but only
increases compressed air consumption and ac-
celerates wear on the device.
□
Switch on the compressor.
□
Allow the compressor to run once long enough
until maximum tank pressure is reached and
the device is switched off.
□
Place the compressed air tacker on the work-
piece and press the trigger
NOTE: The compressed air tacker is
equipped with a trigger lock
.........................................................................Seite 10
tener will only leave the device when the
mouth of the compressed air tacker is
pressed against the workpiece and the
trigger is actuated.
2
Handling the tool
Note the section with special safety references of
these operating instructions. Having checked that
.........................................Seite 12
the fastener driving tool is functioning correctly,
apply the tool to a workpiece and actuate the trigger.
□
Check that the fastener has been driven in cor-
responding to the work requirements.
– If the fastener is protruding, increase the air
pressure in 0.5 bar increments.
– If the fastener is too deep, decrease the air
pressure in 0.5 bar increments.
Operation / Use Operation / Use
Inhaltsverzeichnis
Operation / Use Inbetriebnahme
and pull the maga-
6
of the compressed air
7
.
2
. The fas-
10
GB/IE/NI DE/AT/CH 23 5