Elektro-Automatik ELR 9000 Betriebsanleitung Seite 93

TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Symbols and warnings ..................................5
1.2 Warranty .........................................................5
1.3 Limit of liability ................................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................7
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical data ................................................9
1.8.1 Approved operating conditions ......................9
1.8.2 General technical data ...................................9
1.8.3 Specific technical data (EU models) ...........10
1.8.4 Specific technical data (US models) ...........16
1.8.5 Views ............................................................22
1.9 Construction and function ............................26
1.9.1 General description ......................................26
1.9.2 Block diagram ..............................................26
1.9.3 Scope of delivery .........................................27
1.9.4 Accessories ..................................................27
1.9.5 Options .........................................................27
1.9.6 The control panel (HMI) ...............................28
1.9.7 USB-Port Type B (Back side) ......................31
1.9.8 Interface module slot ...................................31
1.9.9 Analog interface ...........................................31
1.9.10 "Share" connector ........................................32
1.9.11 "Sense" connector (remote sensing) ...........32
1.9.12 Master-Slave bus .........................................32
1.9.13 GPIB port (optional) .....................................32
2
INSTALLATION & COMMISSIONING
2.1 Transport and storage .................................33
2.1.1 Transport ......................................................33
2.1.2 Packaging ....................................................33
2.1.3 Storage .........................................................33
2.2 Unpacking and visual check ........................33
2.3 Installation ....................................................33
2.3.1 Safety procedures before installation and
use ................................................................33
2.3.2 Preparation ...................................................34
2.3.3 Installing the device .....................................34
2.3.4 Mains connection (AC) ................................35
2.3.5 Connection to DC sources ..........................38
2.3.6 Grounding of the DC input ...........................39
2.3.7 Connection of remote sensing ....................39
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
2.3.8
2.3.9
2.3.10 Connecting the analog interface .................41
2.3.11
2.3.12 Initial commission .........................................42
2.3.13 Commission after a firmware update or a
3
OPERATION AND APPLICATION
3.1
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.4.8
3.4.9
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.6
3.6.1
3.6.2
3.7
3.8
3.9
3.9.1
3.9.2
3.9.3
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
ELR 9000 Series
Connecting the "Share" bus ........................40
Installation of an AnyBus interface module .40
Connecting the USB port (rear side) ...........41
long period of non use .................................42
Personal safety ............................................43
Operating modes .........................................43
Voltage regulation / Constant voltage .........43
Current regulation / constant current / current
limitation .......................................................44
Resistance regulation / constant resistance 44
Power regulation / constant power / power
limitation .......................................................44
Dynamic characteristics and stability crite-
ria ..................................................................44
Alarm conditions ..........................................45
Power Fail ...................................................45
Overtemperature ..........................................45
Overvoltage ..................................................45
Overcurrent ..................................................45
Overpower ....................................................45
Manual operation .........................................46
Powering the device ....................................46
Switching the device off ...............................46
Configuration via MENU ..............................46
Adjustment limits ..........................................55
Changing the operating mode .....................55
Manual adjustment of set values .................56
Switching the main screen view ..................56
The meter bars .............................................57
Switching the DC input on or off ..................57
Remote control .............................................58
General .........................................................58
Controls locations ........................................58
Remote control via a digital interface ..........58
Remote control via the analog interface
(AI) ................................................................59
Alarms and monitoring .................................63
Definition of terms ........................................63
Device alarm and event handling ................63
Control panel (HMI) lock ..............................66
Loading and saving a user profile ...............66
The function generator.................................67
Introduction...................................................67
General .........................................................67
Method of operation .....................................67
www.elektroautomatik.de
ea1974@elektroautomatik.de
Page 3