Werbung
BINDING METALBIND
6
BINDING METALBIND
7
1. Use the channel selecting tool for the correct size without covers.
1. Use the channel selecting tool or the chart below to select the correct size channel.
Note!
Note!
The minimum thickness of documents and covers that can be bound with (No. 5) channel must be
If the documents and covers are not thick enough, it is necessary to use a O.FILING Sticky strips avail-
at least 1,8 mm. If the documents and covers are thinner, it is necessary to use a O.FILLING Sticky
able from OPUS supplies, to make it thick enough to bind. When using channels 1.5 to 16 use binding
strips available from OPUS supplies, to make it thick enough to bind. When using channels 5 to 16
bar (B), channels 20 to 32 use the binding bar (A) in the binding slot (3) before you start binding.
use binding bar (B) and channels 20 to 32 use binding bar (A) in the binding slot (3) before you start
binding.
2. Lift the binding handle (1) to the fully open position.
3. Move the clamping lever (2) to the left till it stops.
2. Lift the binding handle (1) to the fully open position.
4. Adjust the extend back support (5) and set it to suit the binding bar being used. For binding
3. Move the clamping lever (2) to the left till it stops.
bar B set the extend back support fully forward. Binding bar A fully back.
4. Adjust the extend back support (5) and set to suit the binding bar being used.
5. Put the Metalbind channel into the binding slot between the binding bars ensuring that the front of the
for binding bar B set the extend back support fully forward. Binding bar A fully back.
channel is facing the front back of the binding slot. When using size smaller than A4 fit a
5. Put the Metalbind channel in-between the binding bars ensuring that the front of
adjustable stop (3) depending which channel is being used. Moving the Metalbind
the channel is facing the front back of the binding slot. When using size smaller than
channel to the maximum left, then close the adjustable stop to hold the channel in place.
A4 fit a adjustable stop (3) depending which channel is being used. Moving the
Important! When using smaller than A4 sizes the channel should be placed in the midle of the
Metalbind channel to the maximum left, then close the adjustable stop to hold
binding slot to ensure even binding pressure a long the metal bind channel.
the channel in place.
6. Push the handle 1 down, the clamping lever (2) will move to the channel automatically to hold channel
Important! When using smaller than A4 sizes the channel should be placed in the midle of the bind-
firmly. Now pull the handle back to the open position.
ing slot to ensure even binding pressure a long the metal bind channel.
7. Ensure pages are even and square, put them between the covers, A4+ there should be a 3 mm space
6. Move the clamping lever (2) firmly to the right until you feel the resistance.
each side from the edge of the covers. A4 size are flush with the edge of the covers.
7. Ensure pages are even, put them between the covers, A4+ there should be a 3 mm
space each side from the edge of the covers, A4 size flush with the edge of the covers.
Note! Make sure that the front cover faces you!
Note! Make sure that the front cover faces you!
8. Put the documents and covers into the Metalbind channel in the binding slot.
• When using A4 size, move the documents and covers to the maximum left, move the adjustable stop
(8) to hold the Metalbind channel in place. Make sure the covers and pages are between the two ex-
METALBIND
BINDING
METALBIND
MB 300 • User guide
channel size
channel size
1,5
3
5
5
7
7
10
10
13
13
16
16
119-148
20
149-186
20
149 – 186
24
187-225
24
187 – 225
28
226-264
28
226 – 264
32
265-303
32
265 – 303
H/p/H - hard cover/pile of pages/hard cover
H/p/H
– hard cover/pile of pages/ hard cover
H/p/T - hard cover/pile of pages/transparent cover
H/p/T
– hard cover/pile of pages/transparent cover
MB 300 • User's guide
Number of pages for binding
Number of pages for binding
H/p/H
H/p/T
H/p/H
H/p/T
-
-
-
-
18-31
18-33
18-31
18-33
32-60
34-63
32-60
34-63
61-89
64-92
61-89
64-92
90-118
93-121
90-118
93-121
119-148
122 - 150
122-150
151-189
151 – 189
190-228
190 – 228
229-266
229 – 266
267-305
267 – 305
S/p/S - soft cover/pile of pages/soft cover
S/p/S – soft cover/pile of pages/soft cover
O/p/O - pile of pages bound only with a channel
O/p/O – pile of pages bound only with a channel
8. Put the documents and covers into the Metalbind
channel in the binding slot (3). If they are extrusions
at each end of the channel ensure the pages and cov-
ers are between them.
trusions in the channel.
9. Push the handle (1) down. If you do not any pressure
NOTE! 5 mm O.CHANNEL Classic and O.SIMPLE CHAN-
or the pressure indicter dose not the correct pressure,
NELS do not have extrusions.
pull the handle back push it once more forward till
If using smaller sizes, make sure that the
the correct pressure shows.
covers pages and the channel with the end
10. Lift the handle (1) to the open position. Move the
of the channel
clamping lever (2) to the left to take out the bound
9. Hold the clamp lever (2) firmly, then push
documents.
the handle (1) a little pull back the handle
then tighten the clamping lever once more
push the binding handle again to bind.
(see Diagram opposite).
10.Open binding handle (1). Move clamping
lever (2) to the left. Now remove bound
covers and documents same time.
5
11.Lift the arm (1). Move the adjusting handle (2) to
EN
S/p/S
O/p/O
S/p/S
O/p/O
1-15
1-15
15-30
15-30
18-34
18-38
18-34
18-38
35-63
39 - 67
35-63
39-67
64 - 92
68 - 97
64-92
68-97
93 - 121
98 - 126
93-121
98-126
122 -150
127 - 155
122-150
127-155
151-189
156-194
151 – 189
156 – 194
190-228
195-233
190 – 228
195 – 233
229-267
234-271
229 – 267
234 – 271
268-308
272-310
268 – 308
272 – 310
GB
Werbung
