Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Protective gloves must be worn at all times during maintenance and
cleaning work.
Pos: 13.9.1 1 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Bet rieb sstoffe - Sch utzau srüst ung/Date nblä tter (Moto röl+Kraftstoff) @ 64\mod_ 1579 858 529 841_ 6.docx @ 625 402 @ @ 1
•
When handling operating fluids, such as engine oil and fuel, suitable protective
equipment (e.g. suitable protective gloves) must be worn.
The data sheets of the operating fluids must be observed.
Pos: 13.9.1 2 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Zü ndkerzens tecker a bziehe n Mäher @ 25\mod _13 7716 077 034 4_6.do cx @ 18 705 4 @ @ 1
Maintenance and cleaning work may only be carried out on level surfaces
with the engine switched off and the spark plug connector disconnected.
Regular maintenance is essential for safety and top performance.
Pos: 13.9.1 3 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Kerzen stecke r niema ls bei laufendem Mo tor ab ziehen @ 13\mod _12 8021 905 695 6_6.do cx @ 1 1007 3 @ @ 1
•
Never remove the plug connector when the engine is running!
Risk of electric shock.
Pos: 13.9.1 4 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/Kerzenste cker n ur be i abgeküh ltem Moto r abz iehen @ 53\mod_ 151 300 1243 580 _6.do cx @ 57 7230 @ @ 1
•
Only remove the plug connector once the engine has cooled down.
Risk of burns!
Pos: 13.9.1 5 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Auf fe sten Sit z des Zündke rze nstecke rs a chten @ 53\mod _151 300 352 3258 _6.do cx @ 57 725 8 @ @ 1
•
Make sure the spark plug connector is fitted tightly. Risk of electric shock.
Pos: 13.9.1 6 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Tank nu r im Fre ien ent leeren @ 0\mod_ 111 5186 486 750 _6.docx @ 267 @ @ 1
•
If the tank has to be emptied, this should be done in the open, and with a cold
engine. Take care to ensure that no fuel is spilt.
Pos: 13.9.1 7 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Nu r Origi nalersatzteile ve rwenden SABO+JD @ 2 6\mod_1 3771 684 882 08_6. docx @ 1 875 31 @ @ 1
For reasons of warranty and safety, only genuine spare parts may be used.
Non-equivalent spare parts can damage the machine and are a safety hazard.
Pos: 14.1 /---------- 1 Leerzeile ---------- @ 0\mod_111 461 1787 140 _6.do cx @ 41 @ @ 1
Pos: 14.2 /Innente il/Be sch reib ung de r Ba uteile/1 BE SCHRE IBUNG DER BAUT EILE @ 0\mo d_11 151 878 9246 8_6. docx @ 2 71 @ 1 @ 1
7 DESCRIPTION OF COMPONENTS
Pos: 14.3 /Innente il/Be sch reib ung de r Ba uteile/ Bil d JS6 3 VARIO C SA2 2211 9 @ 6 3\mod_1 5746 931 968 43_0. docx @ 6 217 81 @ @ 1
Pos: 14.4 /Innente il/Be sch reib ung de r Ba uteile/ Bes chre ibun g der Baute ile JS63 VAR IO/C/JS6 3V/C SA1721 Tex t @ 66\mo d_15 946 384 8443 2_6. docx @ 6 355 08 @ @ 1
1
Engine stop safety control bar
2
Vario actuation
3
Drive control bar
4
Tank cap
5
Engine cover
6
Air filter
7
Spark plug
8
Exhaust protection grill
9
Belt drive covers
10 Splash guard
11 Bar height adjustment
12 Oil filling nozzle with dipstick
13 Starter cable grip
Pos: 15.1 /---------- 1 Leerzeile ---------- @ 0\mod_111 461 1787 140 _6.do cx @ 41 @ @ 1
Pos: 15.2 /Innente il/Vo rbe reiten de Arbei ten/1 VOR BEREITEND E AR BE ITEN @ 0\mod_ 1115 194 917 734_ 6.docx @ 291 @ 1 @ 1
8 PREPARATION
Pos: 15.3 /Innente il/Vo rbe reiten de Arbei ten/Vo rbe reiten de Arbeite n Text 53-PR O M VARIO SABO+JD @ 43\mod _146 416 254 4375 _6.do cx @ 49 769 6 @ @ 1
The following parts are included in the packaging for assembly of the mower:
•
Mower with preassembled guide bar
•
Tool bag with the following contents:
–
Operating instructions with declaration of conformity
–
Warranty conditions (depending on model)
–
Various fixing parts.
In the unlikely event of a missing part, please contact your dealer.
Pos: 15.4 /Innente il/Vo rbe reiten de Arbei ten/Vo r Monta ge... Holm und... Sta rterseil halte r... Zündke rzen stecke r abz iehen! H inweis @ 32\mod _14 0844 122 947 5_6.do cx @ 23 912 1 @ @ 1
ATTENTION
Always remove the spark plug connector before fitting the bar and starter cable
holder, and when folding the bar out. Following assembly, at the latest before
starting the engine, push the spark plug connector back in place.
Pos: 15.5 /Innente il/Vo rbe reiten de Arbei ten/1.1 Füh ru ngsho lm hoc hste llen ( Abbil dung A1 + E 1 + B1) @ 0\mod_1 1256 442 247 79_6 .docx @ 951 @ 2 @ 1
Raise the guide bar (figure A1 + E1 + B1 )
Pos: 15.6 /Innente il/Vo rbe reiten de Arbei ten/Führung sholm h ochs telle n Text JS63 Hi nweis @ 3\mo d_1 1587 388 2214 9_6. docx @ 2 019 2 @ @ 1
IMPORTANT:
Ensure that the Bowden cables are not kinked or trapped when raising the
guide bars!
Pos: 15.7 /Innente il/Vo rbe reiten de Arbei ten/Kabel ni cht kn icken ode r einkle mmen W ICHTIG @ 5 8\mod_1 5671 493 929 84_6 .docx @ 6046 82 @ @ 1
IMPORTANT
Make sure that the cables are not pinched, squeezed, twisted or overstretched
when the guide bars are folded apart or collapsed! Always run the cables along
the outside of the bar connection. A damaged cable may result in a technical
defect of the device.
Pos: 15.8 /Innente il/Vo rbe reiten de Arbei ten/Führ ung sholm h ochs telle n Text JS63 @ 3\mod _11 587 3219 069 4_6.d ocx @ 2 0182 @ @ 1
–
Carefully take the mower out of the shipping box.
–
Remove the wing nut (B) and the saucer-head screw (D) on both sides A1 .
–
Open out the Z-shaped folded guide bar by pulling upwards.
–
Lift the upper guide bar section until upper and lower section of the guide bar are
at one level.
(Figure E1)
–
The quick-release clamps for attachment of the upper and lower section of the bar
are preset by the manufacturer.
1.
Pull up the quick-release clamp to the bar.
2.
Tighten the screws by hand.
3.
Open the quick-release clamp.
4.
Tighten the screw by 1/4 to 1/2 turn.
5.
Pull up the quick-release clamp again and check whether the bars are firmly
connected. Correct if necessary.
–
Keep this setting. If the connection becomes loose over time, the screws
must be tightened.
–
Carefully pull back the guide bars and align the bore in the lower bar section with
the desired height adjustment opening in the holder (C) B1 .
Three different handlebar heights can be set.
–
Plug the screw (D) from the outside on both sides through the holder and lower bar
section, and tighten it to the knurled nut (B). Use the same opening in the
holder (C) on both sides B1 .
–
Attach the Bowden cables to the lower bar with the help of cable ties from
the tool bag.
Pos: 15.9 /Innente il/Vo rbe reiten de Arbei ten/Holm höhenve rstel lung ...Umsc hlagen des Hol ms Hi nweis JS63 @ 14\mod_ 1285 845 829 023_ 6.docx @ 119 259 @ @ 1
CAUTION
When operating the bar height adjustment, the bar may turn over
unintentionally when loosening the wing nuts (B) B1 and the attachment
screws (D) between the lower bar section and the holder. In addition, this
may result in crushed points between the bottom of the bar and the holder.
This may result in risk of injury.
Pos: 15.10 / Innen teil/ Vorbe rei tende Arbe iten/1.1 Holms tart-Montage ( Abbi ldun g L1 ) @ 0\mod_1 1279 863 524 85_6. docx @ 1 414 @ 2 @ 1
Handle starter assembly (figure L1 )
Pos: 15.11 / Innen teil/ Vorbe rei tende Arbe iten/Mon tage Starte rse ilhal ter Text Mo torbrem se @ 37\mod _14 361 9023 917 6_6.do cx @ 3 9970 6 @ @ 1
–
Remove the starter cable holder (1) from the tool bag.
–
Unscrew the nut until the two halves can be pushed over the bar.
–
There is a sticker (2) on the top bar showing the position of the starter
cable holder.
ATTENTION
For reasons of safety, the starter cable holder may only be fitted
in the prescribed position.
–
Press the engine stop control bar (3) onto the upper bar section (4) and hold it
there; pull out the starter cable (5) and insert it into the starter cable holder.
–
Fit the two halves together (6), re-tighten the nut. This prevents the starter cable
from popping out.
The starter cable holder must be fitted / aligned in such a way that the starter cable
is freely accessible and does not rub against any other parts.
Pos: 15.12 / Innen teil/ Vorbe rei tende Arbe iten/1.1 Vo rderräde r verriegel n und en triegeln (JS63 VAR IO C, JS63 VC) (Abbi ldun g T3 ) @ 66\mo d_1 5946 391 4209 4_6. docx @ 6 355 92 @ 2 @ 1
Pos: 15.15 / Innen teil/ Vorbe rei tende Arbe iten/1.1 Sc hni tthöhe e ins tellen @ 4\mod_ 1159 264 261 106_ 6.docx @ 210 22 @ 2 @ 1
Adjusting the cutting height
Pos: 15.16 / Innen teil/ Sic herhe its hinwei se/Si cherheit shinwei s: Messe r, Moto rStop @ 0\mod _11 152 0137 618 7_6.d ocx @ 3 39 @ @ 1
For explanation of symbols, see the table on page 3
Pos: 15.17 / Innen teil/ Vorbe rei tende Arbe iten/Ei nste llun g der Vorderradhö he Text JS6 3 VARIO/C/JS63 V/C @ 6 6\mod_1 5946 393 512 37_6. docx @ 6 356 21 @ @ 1
Front wheel height adjustment
By means of a height adjustment lever at the left front wheel, both front wheels
can be set.
–
Set the height adjustment lever to the desired position.
Pos: 15.18 / Innen teil/ Vorbe rei tende Arbe iten/Ei nste llun g der H inte rra dhöhe Text J S63 @ 3\mod_ 115 8746 223 338_ 6.docx @ 202 82 @ @ 1
Rear wheel height adjustment (figure V3 )
By means of a height adjustment lever at the left rear wheel, both rear wheels
can be set.
–
Slightly lift the device by hand at the lower bar to unload the wheel.
6
Safety information!
Werbung
Inhaltsverzeichnis
