Installation Information - Kärcher KM 100/120 R Bp Originalbetriebsanleitung

3. Unscrew the left knurled screw.
Illustration Q
Left knurled screw
1
Bearing plate
2
Cover plate
3
Right knurled screw
4
4. Pull out the bearing plate.
5. Unscrew the right knurled screw.
6. Pull off the cover plate.
7. Pull out the roller brush.
Illustration R
Roller brush
1
Roller brush mount (on both sides)
2
Tip of an arrow-shaped tapered bristle strip
3
Check:
8. Check the roller brush for wear, damage and wrapped flexible
objects such as ribbons, strings, etc. Replace the roller brush
if it is worn, damaged or the cleaning result is not satisfactory,
or remove wrapped objects.
Installing:
9. Install the roller brush.
Ensure correct alignment, the tips of the arrow-shaped ta-
pered bristle strips must point in the travel direction when driv-
ing forwards.
10.Install the cover plate.
Illustration Q
Left knurled screw
1
Bearing plate
2
Cover plate
3
Right knurled screw
4
11.Tighten the right knurled screw.
12.Install the bearing plate.
13.Tighten the left knurled screw.
14.Close the left-hand cladding, see chapter Open/close the left/
right cladding.
Checking/removing/installing the side brushes
The floating bearing of the side brushes ensures that the sweep-
ing pattern automatically adjusts itself when the bristles are worn.
1. Switch off the machine, see chapter Switching off the ma-
chine.
Check:
2. Check the side brush for wear, damage and wrapped flexible
objects such as ribbons, cords, etc. Replace the side brush if
it is worn, damaged or if the cleaning result is not satisfactory,
or remove wrapped objects.
Illustration P
Side brush
1
Screw (3 pieces)
2
Removal:
3. Unscrew the screws.
4. Remove the side brush.
5. Clean the side brush holder.
Installation:
6. Attach the new side brush to the side brush holder.
7. Tighten the screws.
Adjusting/removing/installing the sealing strips
Note
The trailing distance of the front and rear sealing strip defines
how much the sealing strips fold backwards when driving the de-
vice forwards.
Adjust the side sealing strips accordingly; for adjustment values,
see table Adjustment values sealing strips.
1. Switch off the machine, see chapter Switching off the ma-
chine.
Setting:
2. Open the corresponding cladding, see chapter Open/close
the left/right cladding.
3. Loosen the screws or nuts on the fixing plate of the corre-
sponding sealing strip.
Illustration S
Fastening plate
1
Side sealing strip
2
Front sealing strip
3
Rear sealing strip
4
4. Adjust the appropriate sealing strip by shifting it in the elongat-
ed holes.
5. Tighten the screws or nuts on the fixing plate of the corre-
sponding sealing strip.
Removing/installing:
6. Unscrew the screws or nuts on the fixing plate of the corre-
sponding sealing strip.
7. Remove the fixing plate and the sealing strip.
8. Installation is performed in reverse sequence.

Installation information

Adjust the sealing strip before tightening the screws or nuts.
9. Close the left or right-hand cladding, see chapter Open/close
the left/right cladding.
Table for Adjustment values for sealing strips:
Sealing strip
Side sealing strip
Front sealing strip
Rear sealing strip
Removing/cleaning/installing the dust filter
DANGER
Health risk from dust
Wear a dust mark and safety goggles when working on the filter
system.
Observe the safety instructions on the handling of fine dust.
1. Switch off the machine, see chapter Switching off the ma-
chine.
Removing:
2. Wait at least 1 minute until the automatic dust filter cleaning
has finished and the dust has settled in the filter box.
3. Grasp the recessed grip and swing the storage area upwards.
Illustration T
Storage area
1
Recessed grip
2
Lever
3
Dust filter
4
4. Move the lever to the right into the lock.
5. Remove the dust filter upwards.
Cleaning:
6. Check the dust filter for dirt and damage, clean or replace if
necessary.
ATTENTION
Do not clean or brush out the dust filter with compressed air. To
clean, gently tap or vacuum.
Installing:
7. Installation is performed in reverse sequence.
Removing/installing the rear wheel
DANGER
Danger of death when lifting the machine!
A danger of death from slipping off the jack exists when lifting the
machine.
Never sit or lie down under the raised machine.
Only lift the machine when it is standing on firm, horizontal ground
and secure the machine against rolling away.
Only lift the machine with suitable jacks designed for the weight
of the machine.
Only use jacks at the points marked on the vehicle frame.
English
Adjustment value
Distance from ground 1–3 mm
Trailing distance 10-15 mm
Trailing distance 5-10 mm
29