Mounting The Support Legs To Main Cabinet - Pit Boss 3 Serie Montage Und Betrieb

3. MOUNTING THE SUPPORT LEGS TO MAIN CABINET

Parts Required:
1 x Main Cabinet (#7)
4 x Support Leg With Wheel (#15)
¼–20x½" Screw ( #B)
12 x
Installation:
• Prepare the four support legs for installation, arranging the labeled legs as
shown in illustration 3A.
IMPORTANT: The four support legs must be arranged correctly to be able to
properly install the support panels and support bar in a later assembly step.
• Mount one support leg to the smoke cabinet using three screws. Repeat
installation for the other three support legs. Note illustration 3B.
4. SECURING THE CONTROL BOARD TO SUPPORT LEGS
Parts Required:
2 x #10–24x½" Screw ( #D)
Installation:
• Near the Control Board, loosen the two screws connecting the front panel
to the main cabinet. Note 4A.
• Next, using another two screws, secure the front panel sides to the front-
facing support legs. Once these screws are tight, re-tighten the two screws
that were previously loosened. Note 4B.
5. MOUNTING THE SUPPORT PANELS
Parts Required:
2 x Support Panel (#11)
8 x #10–24x½" Screw ( #D)
Installation:
• Install one support panel to the side of the unit between a front and back
support leg. Secure using two screws on each side. Ensure the flat side of
the support plate is facing outwards. Repeat the same installation to mount
the other support panel. Note illustration for support panel arrangement.
NOTE: The support panel with two holes along the bottom should be on
the same side of the unit as the power cord exits the control board (left
side). This is important for later steps.
6. SECURING THE SUPPORT BAR
Parts Required:
1 x Support Bar (#12)
4 x #10–24x½" Screw ( #D)
Installation:
• Install the support bar to the rear of the unit between the two rear support
legs. Secure using two screws on each side. Ensure the support bar is placed
on the underside of the main cabinet, facing inwards. Note illustration for
support bar arrangement.
8
3A
15-1 15-3
15-2
15-4
3B
15-3
B
15-4
B
15-1
B
15-2
B
4
4A
These 2 Screws were
pre-assembled
4B
D
D
5
D
11
D
D
11
D
6
12
D
D
7. MOUNTING THE POWER CORD BRACKET
Parts Required:
1 x Power Cord Bracket (#10)
2 x #10–24x½" Screw ( #D)
Installation:
• Locate the two holes on the bottom of the (left side) support panel. Mount
the power cord bracket to the support panel using two screws, as shown in 7A.
• Next, loosen the nut on the pre-mounted clip bracket and guide the power
cord through the clip bracket. Once through, tighten the nut, and wrap the
power cord on the bracket until unit is in use. Note 7B, 7C.
8. SECURING THE GREASE TRAY BRACKETS
Parts Required:
2 x Grease Tray Brackets (#17)
#10–24x½" Screw ( #D)
4 x
Installation:
• Secure the grease tray brackets onto the base of the auger housing and
the wire components housing using two screws in each bracket. Note
illustration for proper placement.
NOTE: The diveted end of the brackets should face the control board.
• Fully-tighten all screws on the cart base. Next, carefully turn the unit into
an upright position, with the wheels on the bottom. Ensure its level.
9. PLACING THE GREASE TRAY
Parts Required:
1 x Grease Tray (#16)
Installation:
• Slide the grease tray into the grease tray brackets on the front underside of
the main cabinet, under the control board.
NOTE: The grease tray is completely inserted once the front of the tray
is pushed in as far as it can go, with no gap between the grease tray and
the front panel.
10. ATTACHING THE HOPPER CLEAN-OUT DOOR KNOB
Parts Required:
1 x Door Knob (#A)
Installation:
• Attach the door knob to the hopper clean-out door by rotating the part
into the hole on the door. Rotate until completely fastened and clean-out
door latch is secured.
NOTE: To use the hopper clean-out feature, simply loosen the door knob,
raise the clean-out door latch and open the door.
7A 7B
10
D
D
7C
10
8
D
17-1
17-2
9
FRONT
16
10
A
9