Parts & Specs; Assembly Preparation; Assembly Instructions; Mounting The Grease Exhaust Tube - Pit Boss 3 Serie Montage Und Betrieb

PARTS & SPECS
Part# Description
1 Cooking Grids (x4)
2 Cooking Grid Support Brackets (x10)
3 Chimney Cap (x1)
4 Chimney Stack (x1)
5 Back Handle (x1)
6 Lid Stopper (x1)
7 Main Cabinet (x1)
8 Cabinet Door Handle (x1)
9 Cabinet Door Latch (x1)
10 Power Cord Bracket (x1)
11 Support Panel (x2)
12 Support Bar (x1)
13 Water Pan (x1)
14 Flame Tamer (x1)
15 Support Leg With Wheel (x4)
16 Grease Tray (x1)
17 Grease Tray Brackets (x2)
18 Grease Exhaust Tube (x1)
19 Heat Shield (x1)
20 Meat Probe (x1)
A Door Knob (x1)
B ¼–20x½" Screw (x12)
C ¼–20x⅝" Screw (x4)
D #10–24x½" Screw (x32)
E #10–24x⅓" Screw (x2)
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact
Customer Service if parts are missing when assembling the unit.
PB – ELECTRIC REQUIREMENTS
220-240V, 1.1 AMP, 50HZ, 250W, 3-PRONG GROUNDED PLUG
MODEL UNIT ASSEMBLED (WxHxD) UNIT WEIGHT COOKING AREA
555mm x 1,339mm x 640mm 45.0 kg
PB
PBV3PU1
/ 21.8" x 52.7" x 25.1" / 99.2 lb
6
3
2
4
1
5
6
7
9
8
11
10 15
12
17-1
15-2 15-4
13
14
15-1 15-3
20
A D
B E
C
TEMP. RANGE DIGITAL FEATURES
Ten temperature
Cubic Cooking: 0.08 m / 2.8 ft 65-215°C presets, start-up and
3 3
TOTAL - 5,077 cm² / 787 sq. in. / 149-419°F cool-down cycles,
electric igniter
Parts are located throughout the shipping carton, including underneath the grill. Inspect the grill, parts, and hardware blister pack after
removing from the protective shipping carton. Discard all packaging materials from inside and outside of the grill before assembly, then
review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt to assemble. Shipping damage
is not covered under warranty. Contact your dealer or Pit Boss Customer Service for parts: Monday through Sunday, 4am - 8pm PST (EN/
FR/ES).
service@pitboss-grills.com | Toll-Free: 1-877-303-3134 | Toll-Free Fax: 1-877-303-3135
IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.
Tools required for assembly: screwdriver and level. Tools not included.
IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws completely
until all screws for that step have been installed, or unless otherwise mentioned.

1. MOUNTING THE GREASE EXHAUST TUBE

Parts Required:
1 x Grease Exhaust Tube (#18)
2 x #10–24x⅓" Screw ( #E)
16
Installation:
• Place a piece of cardboard on the floor to prevent scratching the unit and
parts during assembly. First, lift the main cabinet door off the hinges, and
17
place aside. Note illustration 1A
17-2
• Next, flip the main cabinet, bottom side pointed upward, on the cardboard.
18
• Mount the grease exhaust tube to the underside of the main cabinet using
two screws. Note illustration 1B
19
IMPORTANT: Ensure there is a good seal to the main cabinet, as grease
will come from the main cabinet, flow through the exhaust tube, and
exit into the grease tray.

2. ATTACHING THE HEAT SHIELD

Parts Required:
1 x Heat Shield (#19)
2 x #10–24x½" Screw ( #D)
Installation:
• Position the heat shield between the control board and the grease exhaust
tube. Secure using a screw on each side.
IMPORTANT: If this part is not installed correctly, the heat and/or splatter
from the grease exhaust tube may cause damage to the control board.
Grease damage to the rear of control board is not covered by warranty.

ASSEMBLY PREPARATION

ASSEMBLY INSTRUCTIONS

1A
1B
18
2
7
E
19
D
7