A1 List Of The Special Options - FLEISCHMANN TWIN-CENTER 6802 Handbuch

6802_10_12_04_Handbuch_GB
overloaded by too many locomotives
and illuminated trains. It has become
too hot during the running session
and has switched itself off.
Solution: Separate your layout into several
electrically isolated sections, and
feed these with additional external
boosters (i.e. TWIN-BOOSTER 6807
or FMZ-Booster 6805 with Adapter-
Set 6885).
Fault: The red LED (stop) continually
blinks.
Cause: A short circuit has occurred some-
where on the tracks, or the TWIN-
CENTER has become overheated, or
a short circuit has occurred on the
track connection of an external boo-
ster.
Solution: Note the error indication in the TWIN-
CENTER display. Locate the cause of
the short circuit and remove it and
then wait until the TWIN-CENTER has
cooled down.
Fault: Individual locos will not run.
Cause: The loco decoder is not being run in
the correct format. The decoder is
cannot send back any information to
the TWIN-CENTER, or the TWIN-
CENTER cannot automatically distin-
guish, by simply calling up the loco
address, which data format is neces-
sary to control the relevant decoder.
Solution: Check the data format of the loco
decoder and set each individual
decoder to the correct data format
(chapter 7.8).
Fault: Some electrically operated
accessories will not operate.
Cause: The electrical accessory receiver
modules are receiving their com-
mands in the wrong data format,
because they use a different data for-
mat to that which has been set in the
TWIN-CENTRE.
Solution: Check the data format of the acces-
sories which are not working and set
virtual addresses in the menu basic
setting - point setting - which are cor-
rect for each accessory in use.
01.03.2007 13:58 Uhr
19 Problems and Solutions · Supplement A1
Seite 145
A1: List of the Special Options
ADVICE
As for the problem of longer/short
addresses, we will give you some extra
information to adjust some Special Opti-
ons.
In version V1.100 of the TWIN-CENTER software,
it will always be, that when writing or reading a
long loco-address of the loco-decoder so set,
that it now only will react to the long address
(128...999) and not to the short (1...127). That's
because in CV29, bit 5, a so-called "indicator"
has been set (CV29 bit 5=1). If the loco is to be
controlled using the shorter address once more,
then this indicator must be reset (CV29 bit 5=0).
From software V1.100 of the TWIN-CENTER the
behaviour of the address indicator can be adju-
sted using the special option SO662. The value of
the special option is made up of different part
values, each according to which behaviour is sel-
ected.
Setting the address indicator for short/long
addresses according to the reading/writing:
Part value 1: Use the long address after reading
the long address -> CV29.5=1
Part value 2: Use the long address after writing
the long address ->CV29.5=1
Part value 8: use the short address after reading
of CV1 (short address) -> CV29.5=0
Part value 16: use the short address after wrinting
of CV1 (short address) ->CV29.5=0
Example: if this long address is to be used after
writing/reading, or this short address is to be
used afterwriting/reading (CV1), then the value of
the special option should
(27=1+2+8+16). However, if after writing/reading,
the long address should be set to this, or when
writing/reading the short address should not be
set back to this, then the value of the special opti-
on should be SO662=3 (3=1+2). This now corre-
sponds to the instructions of the software V1.100.
be SO662=27
145