Changing The Points / Signals - FLEISCHMANN TWIN-CENTER 6802 Handbuch

6802_10_12_04_Handbuch_GB
8 The Keyboard Mode for Changing Points and Signals
• Search through by pressing the [↓] key
several times until the entry "Virtual
Addrs" is reached
• Continue with the [→] key
VAdd DAdd
1 65
• Under "VAdd" in the first column, enter
your point number (=virtual address), in
this example 1
• Continue with the [→] key
• In the second column under "DAdd",
enter the digital address of the electrical
accessory receiver module
• Continue with the [→] key
• In the third column under "Out" enter the
number of the output on which the elec-
trical accessory receiver module is
connected (1 -4)
• Continue with the [→] key
• In the fourth column under "DF" enter
the digital format "F" = FMZ, or "D" =
DCC by pressing the [+] or [↓] key
accordingly
• Confirm the choice by pressing the [↵]
key
• Return to running with the [menu] key
Instead of leaving the notification menu with the
[menu] key, by pressing the [←] key three times,
you return to the fourth column. Now further vir-
tual addresses can be entered together with their
accompanying details (see the box above).
IMPORTANT
The decoder addresses of the receiver
modules are not the same as the virtual
addresses by which the points and sig-
nals in all menus will be called up by the
TWIN-CENTER.
8.2

Changing the Points / Signals

Mode preselection
The TWIN-CENTER knows 4 different operational
modes: Keyboard, Memo, s88 and Program-
ming. The current individual mode setting is dis-
played in the centre section of the display.
In order to transfer from one mode to another,
using the software V1.000, it is necessary to
120
01.03.2007 13:58 Uhr
Out DF
1 F
Seite 120
press the [mode] key several times until the desi-
red mode is shown in the display.
However, using the software V1.100 it is now
possible to directly dial up the desired mode,
simply by pressing the [mode] key and then the
suitable number, before the TWIN-CENTER
shows the next mode in the display:
1-Keyboard 2-Memo
gramming
The elapsed time for the direct selection of a
mode as set at the factory is 1 second, but this
may be altered in special option S0817 in steps
of 10 milliseconds.
SO817 is preset to =100 (100 * 10ms = 1s).
Points and signals, which - as described in the
passage above - have been previously notified,
are actually operated in the "keyboard mode". If
the TWIN-CENTER is not currently set to "keybo-
ard mode", then this need to be set. Each time
the [mode] key is pressed the operational mode
will be changed and shown in the display. Press
the [mode] key as required until the display indi-
cates "keyboard mode".
In the operational "keyboard mode" the individu-
al points and signals can be set by using the cen-
tral block of keys of the TWIN-CENTER (numbers
0 to 9 as well as the special key C, [+], [↵], [↓], [←]
and [→]. These 16 keys represent 8 pairs of keys
which will directly change 8 points or signals. The
8 pairs of keys are set out in two rows. in the
upper row the pairs 1 - 4 for points/ signals num-
bers 1 to 4, and in the lower row pairs 5 - 8 for the
points/ signals 5 to 8.
In operation mode "keyboard" the keys
have another definition.
On the TWIN-CENTER keyboard the keys are desi-
gnated 0 - 9 and the special signs C,[+], [↵], [↓],
[←] and [→].
3-s88 4-Pro-
They are then
indicated as key
pairs for points /
signals.