Terminal Connection Diagrams; Connection Of Transmitter Models To Peripherals - ABB CoriolisMaster serie Inbetriebnahmeanleitung

Change from two to one column
5.6

Terminal connection diagrams

5.6.1

Connection of transmitter models to peripherals

Models FCB330, FCB350, FCT330, FCT350
1+ 2-
L
51 52 81 82 41 42 31 32 33 34
4
Fig. 20
1 Power supply | 2 Current output 1 | 3 Current output 2 | 4 Pulse output | 5 Digital switching output | 6 Digital switching input |
7 Equipotential bonding (PA)
IMPORTANT (NOTE)
When using the device in hazardous areas, note the additional connection data in the chapter titled "Technical data relevant to
hazardous areas"!
Terminal Function
L / N / PE Power supply, 100 ... 230 V AC, 50/60 Hz
1+ / 2- / PE Power supply
— 24 V AC, 50/60 Hz
— 24 V DC
31 / 32 Current output 1, active
0/4 ... 20 mA , (0 Ω ≤R
Current output 1, passive
4 ... 20 mA (0 Ω ≤R
33 / 34 Current output 2, passive
4 ... 20 mA (0 Ω ≤R
51 / 52 Pulse output, passive
fmax = 5 kHz, pulse width = 0.1 ... 2000 ms, 0.001 ... 1000 pulses/unit
— "Closed": 0 V ≤ U
— "Open": 16 V ≤ U
Pulse output active, U = 16 ... 30 V, load ≥ 150 Ω, fmax = 5 kHz
41 / 42 Digital switching output, active
— "Closed": 0 V ≤ U
— "Open": 16 V ≤ U
81 / 82 Digital switching input, passive
— Input "On": 16 V ≤ UKL ≤ 30 V
— Input "Off": 0 V ≤ UKL ≤ 2 V
- Equipotential bonding "PA"
When the FCT300 transmitter is connected to the FCB300 flowmeter sensor, the transmitter must also be connected to "PA".
N 31 32 33 34 51 52 41 42 81 82
1 2 3 4
5 6 2 3
≤560 Ω, FCT300-A1/F1:1 0 Ω ≤R
B
≤600 Ω), source voltage 12 ≤U
B
≤600 Ω), source voltage 12 ≤U
B
≤ 2 V, 2 mA ≤ I ≤ 220 mA
CEL CEL
≤ 30 V DC, 0 mA ≤ I
CEH
≤ 2 V, 2 mA ≤ I ≤ 220 mA
CEL CEL
≤ 30 V DC, 0 mA ≤ I
CEH
7
7
5 6
2- 1+
N L
7
1
≤300 Ω)
B
≤ 30 V
q
≤ 30 V
q
≤ 0.2 mA
CEH
≤ 0.2 mA
CEH
7
CoriolisMaster FCB330, FCB350 | CI/FCB300-X1 EN - 23
FCB330
FCB350
FCT330 - A1/F1
FCT350 - A1/F1
(Zone 1 / Div. 1)
FCT330
FCT350
G10331