SIP SILVERCUT DISC 340 F FC Betriebsanleitung Seite 133

Instruction for work
General safety instructions
Regular use in agriculture
The machine has been designed strictly for regular
use in agriculture.
If the machine was missused for any other purpose,
and get damaged during irregular use, manufacturer is
not liable for damages caused to the machine. It is the
user himself who bears the risk.
All conditions for work and maintenance, prescribed by
the manufacturer, should strictly be considered.
The machine may only be used, handled and repaired
by persons who are appointed to do this and who are
aware of the dangers.
All relevant safety regulations as well as all generally
used safety tehnical, working-medical and traffic
regulations should be considered during the work with
the maschine.
The manufacturer is not liable for damages, caused to
the machine which has been rebuilt by the user, if
damages had occured as a result of the rebuilding.
Before entering on public traffic roads and
before each starting of the machine and
tractor, check all traffic and working safety
devices!
Safety and antiaccident instructions
1. Besides the instructions from this booklet take
into consideration all generally used safety and
accident regulations!
2. Safety and warning decals, placed on the machine,
give important instructions for safe work. Take
them into consideration for your safety!
3. While driving on public roads, take into
consideration traffic signs and regulations!
4. Make sure you get familiar with all devices and
elements for handling and with the functions,
before starting with the work!
5. Avoid wearing loose-fitting clothes. Clothes should
fit tight to the user's body.
6. To avoid danger of fire, keep the machine clean!
7. Before switching on the machine and driving off,
make sure there is noone near the machine
(children). Make sure your visibility is sufficient!
8. It is prohibited to drive persons on the machine!
9. Implements should be connected according to the
instructions, all prescribed devices fastened to
the prescribed spots and secured!
10. When disconnecting the machine from the tractor,
place it on the flat ground and use support
devices!
11. Special attention is needed when you are
connecting or disconnecting the implement to the
tractor!
12. Always place the charging weights according to
the instructions on the provided fastening points!
13. Respect prescribed pay load, axle load and
transport dimensions!
14. Transportequipment on machine and tractor is to
be tested for traffic safety before each use: lights,
protections etc!
15. Strating devices for remote control (wires, chains,
bars, etc.) should be secured in a way, that they
can not be unintentionally released during
transport or work.
16. For driving on the road, prepare and secure the
machine according to the manufacturers
instructions!
17. Never leave the driver seat during driving!
18. Always adjust the driving speed to the driving
conditions. Avoid fast turning when driving uphill,
downhill or across the slope!
19. The performance during driving and the ability of
turning is changed, when there are implements
connected or mounted to the tractor. Pay
attention to sufficient ability of turning and
braking!
20. In turnings, take into consideration the load which
is outside the centre of gravity and/or constant
weight of the implement!
21. Connect the imlement only when all safety devices
are in position and when the implement is
secured!
22. It is prohibited to be in the working and dangerous
area of the machine!
23. Stay away from the area of swinging and turning
of the machine!
24. Hidraulic flaps, doors etc. may be put in action
only when no one is in the swinging area!
25. On all parts of the machine, which are mecanically
or hydraulically driven, there is danger of shear
and squeeze!
26. Secure the implement before leaving the tractor.
Lower the implement completely. Switch off the
engine and pull out the ignition key!
27. Nobody is allowed to be between the tractor and
the implement if the vehicle is not secured against
movement by a brake or/and by a wedge!
On tractor mounted machines
1. Before mounting and/or dismounting the machine
to or from three point hitch set the handling device
into position that prevents uncontrolled lowering
or lifting of the machine!
2. When mounting the machine on three point hitch
of the tractor, category of fixing points must be or
must be done identical!
3. In the area of 3 point hitch bars there is a danger
of injuries being caused by squeezing and of
bruises!
4. When operating outside lift-control of three point
hitch, don't stay between tractor and machine!
5. When machine in transport position, adjust side
movement of three point hitch!
6. When driving on the road with lifted machine,
insure the lever of hydraulic control against
unintentional drop!
4