Herunterladen Diese Seite drucken

Zipro Pacemaker Bedienungsanleitung Seite 22

Trainings-laufband
Vorschau ausblenden Andere Handbücher für Pacemaker:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 24
The signal cable is
broken or
insulation is worn
The computer is
damaged
The connection
between the
control board and
the computer is
blocked
E02
Incorrect supply
The motor does
voltage
not operate
Incorrect
connection of the
motor cable
The controller is
damaged
E03
Sensor connection
The computer
incorrect
failed to detect
speed sensor
Sensor plug
signal for 15
connection
seconds
incorrect
Sensor failure
E04
Incorrect
Communication
connection or
error
damage to the
wires.
E05
Motor failure
Overload error
Too low rated
current in the
controller.
Current exceeds
the rated value
E06
Supply voltage too
Explosion-Proof
low
Protection.
Short circuit
Incorrect power
supply
Verify plug
connections. If it is
correct and the
problem persists,
contact the customer
service of the
manufacturer's
service.
Contact the
manufacturer's
service.
Contact the
manufacturer's
service.
Make sure the voltage
is correct. If the
problem persists,
contact the customer
service of the
manufacturer's
service.
Disconnect the cable
and connect it again.
If the problem
persists, contact
manufacturer's
service.
Contact the
manufacturer's
service.
Contact the
manufacturer's
service.
Verify plug
connections. If it is
correct and the
problem persists,
contact
manufacturer's
service.
Contact
manufacturer's
service.
Contact
manufacturer's
service.
Make sure the motor
has not burnt out. If
not, disconnect the
treadmill from the
mains and reconnect
it. If the problem
persists, contact
manufacturer's
service.
Replace the
controller. Contact
the manufacturer's
service.
Make sure the weight
of the user does not
exceed the maximum
value for the device.
Connect the device to
the correct voltage.
Contact
manufacturer's
service.
E07
The safety key is
Nothing is
out
displayed
E08
The driver is
EEPROM driver
broken.
error
E09
The device is not
The controller is
placed on a flat
in an inclined
surface.
position
E10
Incorrect
Transient
installation of the
current
driver.
protection
Incorrectly
mounted engine.
The transmission
part of the
treadmill is
blocked.
E11
Check if the AC power is above 270 VAT or it is
Voltage is too
unstable. If so, stop using the treadmill and
high
report it malfunction.
E13
Damaged wires
Communication
between the meter
error between
and the controller.
the meter and
Incorrectly
the controller.
connected socket.
The counter is
not receiving a
signal from the
drive.
E14
Check if the AC power is lower than 160VAC or
Voltage is too
it is
low
unstable. If so, please stop using the product
and report
malfunction.
The device does
No power
not work
The safety key is
out
Short circuit
The ON/OFF switch
is not on
The running belt
The running belt is
does not move
not lubricated
smoothly
enough
The running belt is
too tense
The running belt
The running belt is
is skewed
too loose
The drive belt is
too loose
WARRANTY
On behalf of the Warrantor, the seller grants a 24-month warranty in
the territory of the Republic of Poland starting on the date of sale.
The warranty for the product does not exclude, limit, or suspend any
rights of the Buyer under the Consumer Rights Act.
The warranty card can be found on the last page.
WARRANTY TERMS AND CONDITIONS
1.
The warranty covers only latent defects attributable to the
manufacturer.
2.
The claim shall be processed by the point of sale or technical
service under the warranty if the customer produces:
EN
Insert the safety key.
Contact
manufacturer's
service.
Move device to flat,
stable surface, then
restart.
Contact
manufacturer's
service.
Contact
manufacturer's
service.
Contact
manufacturer's
service.
Contact
manufacturer's
service.
Contact
manufacturer's
service.
Connect the device to
a power source.
Insert the safety key.
Contact
manufacturer's
service.
Turn the device on.
Lubricate the running
belt as per the
manual.
Adjust and centre the
running belt as per
the manual.
Adjust and centre the
running belt as per
the manual.
Contact the
manufacturer's
service.
22

Werbung

loading