Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
en
24 | Start Line TCE 420 |
Content English
1.
Symbols used
1.1
In the documentation
1.1.1
Warning notices -
Structure and meaning
1.1.2
Symbols in this documentation
1.2
On the product
2.
General principles
3.
Maintenance routine
3.1
Air regulator usage and maintain
3.2
Tighten the nuts on equipment at regular
intervals
3.3
Clean the silencer on pedal valves at regular
intervals
4.
Equipment adjustment
4.1
Adjust the angle of demounting head
4.2
Adjust the hex locking plate
4.3
Adjust the square locking plate
4.4
Adjust the square shaft roller
4.5
Adjust fixing bolts and nuts at the lower end of
tilt arm
4.6
Adjust the position of pedal valve rod for bead
break cylinder
4.7
Adjust the position of pedal valve rod for
turntable cylinder
4.8
Adjust the position of pedal valve rod for tilt
cylinder
4.9
Adjust the silencer at top of tilt cylinder valve 30
4.10 Adjust the position of clamps
4.11 Adjust the fixing sleeve of bead break cylinder 31
4.12 Adjust the motor belt
4.13 Adjust the position of switch
5.
Change the components
5.1
Change turntable cylinder and sealing rings
5.1.1
Change turntable cylinder
5.1.2
Change outside sealing rings
5.1.3
Change inside sealing rings
5.2
Change bead break cylinder and sealing rings 32
5.2.1
Change bead break cylinder
5.2.2
Change outside sealing rings
5.2.3
Change inside sealing rings
5.3
Change tilt cylinder and sealing rings
5.3.1
Change tilt cylinder
5.3.2
Change the sealing rings in cylinder
5.4
Change hex shaft locking cylinder and sealing
rings
|
1 695 108 084
2016-11-15
25
5.5
Change square shaft locking cylinder and
25
sealing rings
5.6
Change the handle valve and sealing rings
25
5.7
Change the air guider and sealing rings
25
5.8
Change the pedal valve assembly and sealing
25
rings
5.9
Change exhaust valve and sealing rings
25
5.9.1
Change the exhaust valve
5.9.2
Change sealing rings
26
5.10 Change gearbox
26
5.11 Change the switch
5.12 Change the capacitor
27
5.13 Change motor
5.14 Change the pedal tension spring or torsion
27
spring
28
6.
Trouble
28
6.1
Turntable not rotate
28
6.2
Powerless turntable torsion power
28
6.3
Clamps not move or moves not smoothly
28
6.4
The clamps move automatically
6.5
The clamps cannot fix the rim
29
6.6
Demounting head is wear and tear too fast
6.7
The position of demounting head has change
29
when tilt arm returns back
6.8
Leakage in cylinder
29
6.9
The gearbox not rotate or has big noise
6.10 Hex shaft moves up and down not smoothly
29
6.11 Pedal cannot return back
6.12 Tilt arm cannot tilt or tilt slowly
30
6.13 Bead break blade moves slowly
6.14 Powerless bead break power
31
31
7.
Oil usage
32
8.
Pneumatic schematic dia- gram
32
32
9.
Circuit diagram
32
32
32
32
32
33
33
33
33
33
33
34
34
34
34
34
34
35
35
35
35
36
36
36
36
37
37
37
37
37
37
37
37
37
38
38
38
39
40
Robert Bosch GmbH
Werbung
Inhaltsverzeichnis
