Operating Instructions - Truma Trumatic E 2400 Gebrauchsanweisung

Operating instructions

Always observe the opera ting instructions and "Impor-
tant operating notes" prior to starting! The vehicle owner
is responsible for the correct operation of the appliance!
The installer or vehicle owner must apply the yellow sticker
with the warning information, which is enclosed with the ap-
pliance, to a place in the vehicle where it is clearly visible to
all users (e.g. on the wardrobe door)! Ask Truma to send you
stickers, if necessary.
Control panel with sliding switch
a = Slide valve
Heating – Off – Ventilation
b = Slide valve for
high setting (large flame symbol)
low setting (small flame symbol)
Control panel with rotary switch
c = "Heating" rotary switch
high setting (large flame symbol)
low setting (small flame symbol)
d = "Off" rotary switch
e = "Ventilation" rotary switch
high setting (large symbol)
low setting (small symbol)
Switching on the Heating
– Remove cowl cap.
– Turn on gas cylinder and open quick-acting valve in the gas
supply line.
– Adjust desired room temperature at rotary knob.
– Switching the heating on:
Control panel with sliding switch
Set the switch (a) to Heating and switch (b) to the desired
output setting.
Control panel with rotary switch
Set the rotary switch to the desired output setting (c).
If the outside temperature is low, switch to high setting.
The Trumatic E heater has been tested and approved for
operation, also when the vehicle is moving. The burner
with fan assistance guarantees satisfactory operation, even
under extremely windy conditions. It may be necessary to ob-
serve respective, country-specific regulations for the operation
of liquid gas appliances when the vehicle is moving.
14
b a
Trumatic E
e
d
c
Switching on the Ventilation
Control panel with sliding switch
Set switch (a) to Ventilation and switch (b) to the desired out-
put setting.
Control panel with rotary switch
Set the rotary switch to the desired output setting (e).
Switching off
Set the sliding switch (a) or the rotary switch (d) to the centre.
If the appliance is switched off after a heating phase, the fan
can continue running in order to make use of the residual
heat.
If the appliance is not used for a prolonged period of time,
close quick-acting valve in the gas supply line and turn off gas
cylinder.
Green indicator lamp "Operation"
(under rotary control knob)
When the appliance is switched on (heating or ventilation) the
green indicator lamp must be illuminated (the fan is running).
If the indicator lamp is not illuminated, possibly check the
(main) switch. For this purpose observe respective instructions
of the vehicle manufacturer.
During the heating operation, while the flame is burning, the
green indicator lamp lights up with twice the intensity. This
also makes it possible to determine the instantaneous switch-
ing point of the room temperature.
Fuses
The device and control panel fuses are on the electronic con-
trol unit on the device.
Device fuse (F1):
3.15 AT – slow – (EN 60127-2-3)
Control panel fuse (F3):
1.6 AT – slow –
The fine-wire fuse must only be replaced by a fuse of the
same design.
Red indicator lamp "Failure"
Should a failure occur, the red indicator is illuminated per-
manently. Possible causes for the failure can be e.g. no gas,
insufficient combustion air, heavily soiled rotor, defective fuse
etc.. Deactivate by switching off and then switching on again.
Opening a window to which a window switch is attached
and closing it again is the equivalent of switching the
equipment off and on again at the control panel (e.g. a fault
reset)!
Flash operation indicates that the operating voltage is too
low or too high for the appliance (charge battery, if necessary).
In Germany, always notify the Truma Service Centre if prob-
lems are encountered; in other countries the relevant service
partners should be contacted (see Truma Service Booklet or
www.truma.com).