Choice Of Location; Exhaust Duct - Truma Trumatic E 2400 Gebrauchsanweisung

In-vehicle installations must comply with the technical and
administrative regulations of the respective country of use
(e.g. EN 1949 for vehicles). The national regulations and rules
(e.g. DVGW work sheet G 607 in Germany) must be complied
with.
The relevant employer's liability insurance association accident
prevention regulations must be observed in Germany for vehi-
cles used for commercial purposes (BGV D 34).
In other countries always observe the respectively valid
regulations.
For further details on the rules and regulations in the respec-
tive country of desig-nation, please contact our agencies
abroad (see Truma Service Booklet or www.truma.com).
Notes on the installation in commercial
vehicles
The TÜV-tested cylinder holder (part no. 39742-00) is a con-
stituent of the type approval for Trumatic E heaters in accord-
ance with heater directive 2001/56/EC. Here it is stated that
2 gas cylinders with a contents of max. 15 kg can be con-
nected and used for operating the heaters while the vehicle is
moving. For the protection of the cylinder valve and the gas
pressure regulator, just the protective cover provided with the
cylinder bracket is required.
For protection against theft or for reasons of appearance, the
gas cylinder can also be concealed using the lockable cylinder
cabinet (part no. 39010-21100). The cabinet is bolted with the
cylinder bracket to the vehicle frame.
When installing the heater in special vehicles (e.g. vehicles for
transporting hazardous goods), the respective regula-tions for
such vehicles must be observed.
Notes on installation in driver's cab
For appliances with ex-haust ducts under the vehicle floor, the
exhaust cowl must extend into the area of the side or rear wall
of the cab or vehicle, in order to make sure exhaust gas does
not enter the inside of the vehicle.
Model-related assembly instructions can be obtained from
Truma.
In Germany, for tank vehicles carrying hazardous goods in the
field of application covered by the ADR, the appliance is only
approved with the Truma control unit.
Notes on installation in boats
Installation in boats must accord with the technical and ad-
ministrative provisions of the individual country of use (e.g.
EN ISO 10239 for boats). National specifications and regula-
tions (in Germany, for example, DVGW Worksheet G 608)
must be respected.
The "Guidelines for the Construction, Installation, Testing and
Operation of Liquid Gas Systems for Household Purposes
on Inland Waterways" (BGR 146) must be complied with in
Germany. According to these guidelines the liquid gas system
must be installed by an engineer who has been approved by
the inland waterways employer's liability associations and
tested by experts belonging to these employer's liability insur-
ance associations.
In other countries always observe the respectively valid
regulations.
It is not possible to install heaters with floor cowl.
For further notes on installation, refer to the assembly instruc-
tions for the Trumatic E boat heater.

Choice of location

Always install the appliance and its exhaust duct in such a
way that it is always easily accessible for service work and can
be removed and installed easily.
For evenly distributed heating, the installation of the appliance
should be as much in the centre of the vehicle as possible (or
under the vehicle), and in such a way that the air distribution
ducts can be routed with approximately the same length.
The cowl must be placed in such a way that exhaust gas can-
not find its way into the vehicle interior.
The wall cowl is to be fitted in such a way that no tank nozzles
or tank ventilation apertures are located within 500 mm (R) of
it. In addition, no air discharge apertures for the living area or
window openings may be located with 300 mm (R) of it.
R
If the cowl is being installed directly beneath a window
that can be opened, it must be equipped with an elec-
tric switch. The gas unit must automatically switch itself off
using the Truma automatic shut-off facility if the window is
opened (Accessories, part no. 39050-00800).

Exhaust duct

With the Trumatic E 2400 only use the Truma exhaust duct
AA 24 (part no. 39420-00) for the installation with wall cowl,
and for boats use the Truma stainless steel exhaust duct
AEM 24 (part no. 39430-00) and the combustion air supply
duct ZR 24 (part no. 39440-00) as the appliance has only been
tested and approved with these ducts.
A new O-ring must always be installed after dismantling
the exhaust duct!
300 mm
17