Yamaha CDR-HD1000 Bedienungsanleitung Seite 27

NATURAL SOUND HDD/CD RECORDER CDR–HD1000
POWER
HDD CDR COPY
PHONES LEVEL
MIN MAX
1
<To start copying>
Note
• This unit can make a high-speed copy onto a CD-R or CD-RW
disc. However there are some audio CD-R or CD-RW discs that
do not support high speed writing. To copy onto these discs, lower
the copy speed. (See "Copy Speed" on page 30.)
1.
Press COPY twice.
The following message appears on the display, and this unit
enters in the copy standby mode. Copying has not been started
yet at this stage.
H D D "
ALL SYNC
0 0 3 1 " 1
ALL SYNC
2.
Select the group on the HDD to be copied.
Rotate the MULTI JOG knob (press +/– on the remote control)
to select the group on the HDD to be copied.
3.
Select the copying mode.
Press MODE/SET to select the copying mode. See page 28 for
details.
4.
Make detailed settings for your copying on the menu.
Press MENU to make copying menu settings. See page 29 for
details.
5.
Start copying.
Press w/d (w on the remote control) to start copying.
0 0 3 1 " 1
ALL SYNC
3
TEXT/TIME
TRACK NO.
BOOKMARK
REC FINALIZE
7 7
C D - R W
REC
L
GROUP
dB –30 –10 –6 –2 0
ANLG CD–RW
R
0 0 0
REC
L
GROUP
dB –30 –10 –6 –2 0
ANLG CD–RW
R
0 0 1
REC
L
GROUP
dB –30 –10 –6 –2 0
ANLG CD-RW
R
2 4
7
MULTI JOG
PUSH ENTER
1
MODE/SET MENU
COMPLETE CLEAR
7
DIGITAL REC LEVEL
INPUT ANALOG REC LEVEL
ERASE
OPTICAL
3
COAXIAL
ANALOG
MIN MAX
5 6
Notes
• OPC may start on the loaded disc depending on its recording
condition. It takes approximately 15 seconds to complete the
adjustment.
O P C A d j u s t
When the adjustment has been completed, and the message
above turns off on the display, copying automatically starts.
• The progress of elapsed time for the track being copied may
vary by the data processing inside this unit.
6.
When copying has been completed, the operation of
the HDD and the CD automatically stops. To cancel
copying, press a.
Caution
• If copying is canceled by a being pressed, only the data that
has been recorded on the CD-R or CD-RW disc before the
cancellation remains on the disc. When "Digital Move" (see
page 30) is selected, the original data on the HDD which has
already been copied to a CD-R or CD-RW disc will be
deleted.
7.
The TOC indicator flashes if the copied data contains
the title data (disc title etc.) which can be copied to a
CD-R or CD-RW disc. To copy the titles, perform
finalization before opening the disc tray (See page
19).
"TEXT Save?" appears on the display if the disc tray has been
attempted to be opened by pressing v (OPEN/CLOSE on the
remote control). To copy the title, perform finalization. To open
the disc tray, press v (OPEN/CLOSE on the remote control)
again.
Caution
• If the disc tray is opened without performing finalization, the
title data is not copied to a CD-R or CD-RW disc.
Note
• In the full auto-synchronized copy mode, finalization is
performed automatically.
BASIC COPYING OPERATION
OPEN/CLOSE
COPY REC
HDD
TRACK NO.
FINALIZE ERASE WRITE
TEXT/TIME INPUT
MODE/SET MENU
4
COMPLETE
2
CLEAR ENTER
L GROUP
dB –30 –10 –6 –2 0
CD–RW
R
5
CDR
6
REC
25
E-