Scheppach BASA4 Originalbetriebsanleitung Seite 31

– Check whether the moving parts function
faultlessly and do not jam or whether parts are
damaged. All parts must be correctly mounted
and all conditions must be fulfilled to ensure
fault-free operation of the electric tool.
– The moving protective hood may not be fixed
in the open position.
– Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is spec-
ified in the operating manual.
– Damaged switches must be replaced at a cus-
tomer service workshop.
– Do not use any faulty or damaged connection
cables.
– Do not use any electric tool on which the switch
cannot be switched on and off.
20. Attention!
– The use of other insertion tools and other ac-
cessories can entail a risk of injury.
21. Have your electric tool repaired by a qualified
electrician
– This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
22. Do not use the cable for purposes for which it is
not intended Do not use the cable to pull the plug
out of the outlet. Protect the cable from heat, oil
and sharp edges.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair active
or passive medical implants under certain conditions.
In order to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
Additional safety instructions
• Wear safety gloves whenever you carry out any
maintenance work on the blade!
• When cutting round or irregularly shaped wood, use
a device to stop the workpiece from twisting.
• When cutting boards in upright position, use a de-
vice to prevent kick-back.
• A dust extraction system designed for an air velocity
of 20 m/s should be connected in order to comply
with woodworking dust emission values and to en-
sure reliable operation.
• Give these safety regulations to all persons who
work on the machine.
• Do not use this saw to cut fire wood.
• The machine is equipped with a safety switch to
prevent it being switched on again accidentally af-
ter a power failure.
• Before you use the machine for the first time, check
that the voltage marked on the rating plate is the
same as your mains voltage.
• If you use a cable reel, the complete cable has to
be pulled off the reel.
• Persons working on the machine should not be dis-
tracted.
• Note the direction of rotation of the motor and blade.
• Never dismantle the machineʼs safety devices or put
them out of operation.
• Never cut workpieces which are too small to hold
securely in your hand.
• Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
• Note the information published by your professional
associations.
• Adjustable protective devices have to be adjusted
as close as possible to the workpiece.
• Important! Support long workpieces (e.g. with a
roller table) to prevent them sagging at the end of
a cut.
• Make sure the blade guard (3) is in its lower position
when the saw is being transported.
• Safety guards are not to be used to move or misuse
the machine.
• Blades that are misshapen or damaged in any way
must not be used.
• If the table insert is worn, replace it.
• Never operate the machine if either the door pro-
tecting the blade or the detachable safety device
are open.
• Ensure that the choice of blade and the selected
speed are suitable for the material to be cut.
• Do not begin cleaning the blade until it has come to
a complete standstill.
• For straight cuts of small workpieces against the
longitudinal limit stop the push stick has to be used.
• The bandsaw blade guard should be in its lowest
position close to the bench during transport.
• For miter cuts when the table is tilted, the parallel
stop must be positioned on the lower part of the
table.
www.scheppach.com GB | 31