Fox FLOAT X2 Bedienungsanleitung Seite 3

CONGRATULATIONS!
Thank you for choosing a FOX suspension product for your bicycle. FOX suspension products are designed
and tested by the finest professionals in the industry, in Santa Cruz County, California, USA.
Follow the guidelines and instructions provided in this owner's guide, so that you are able to properly set up,
use, and maintain your new FOX product.
More information and videos are available at http://www.ridefox.com/OwnersManuals, or call FOX US at
1.800.369.7469, email mtbservice@ridefox.com, or contact an Authorized International FOX Service Center
at http://www.ridefox.com/GlobalDistributors. If access to the Internet is not available to you, contact FOX to
order a paper copy of the online FOX owner's manual for your product, free of charge.
FOX products should be installed by a professional bicycle
service technician, in accordance with FOX installation
specifications. Improperly installed forks can fail, causing the
rider to lose control resulting in SEVERE INJURY OR DEATH.
Modification or alteration of a FOX product can cause product
failure resulting in SEVERE INJURY OR DEATH. Never modify or
alter ANY part of a FOX product (including coil springs, lower leg
cross brace, crown, steerer, upper tubes, lower leg, air can, seat
post, air volume spacers, internals, axle slit shims, axle adapters,
or any other parts).
FOX bicycle suspension products may also be used on pedal-
assisted motorized cycles or motorized vehicles that produce
up to 250 watts of power. DO NOT use FOX Bicycle suspension
products on vehicles that produce more than 250 watts of
power.
FOX E-BIKE OPTIMIZED suspension products may be used on
motorized cycles or motorized vehicles producing between 250-
500 watts of power. DO NOT use any FOX bicycle suspension
product on any pedal-assisted motorized cycle or motorized
vehicle that produces more than 500 watts of power.
DO NOT use any FOX bicycle suspension products or FOX
E-BIKE OPTIMIZED suspension products on any pedal-assisted
motorized cycle or motorized vehicle that produces more than
500 watts of power. DO NOT use any FOX bicycle suspension
product on any throttle-equipped motorized vehicle.
Misuse of FOX suspension products may cause the suspension
to fail, resulting in property damage or SERIOUS INJURY OR
DEATH, and void the warranty.
DO NOT use FOX bicycle suspension products on any vehicle
carrying more than one operator or rider, such as a tandem
bicycle or heavy utility bicycle.
Improper service, or use of non-FOX replacement parts with
FOX forks and shocks may cause the product to malfunction,
resulting in SEVERE INJURY OR DEATH.
Never use a power washer to clean your FOX product.
Follow your brake manufacturer's installation instructions for
proper installation and adjustment of the brake system. Failure
to properly install and adjust your brakes can lead to a loss of
control of the bicycle, which can result in SEVERE INJURY OR
DEATH.
WARNING AND SAFETY INFORMATION
Your fork or shock may fail under conditions that cause bending
and/or breaking to any part of the fork or shock. Any condition
that causes a loss of air and/or oil, such as a collision or extended
periods of non-use, may also cause your fork or shock to fail. A
damaged and/or leaking fork or shock can fail, resulting in a crash
and SEVERE INJURY OR DEATH. If you suspect your fork or shock
has been damaged, stop riding immediately and contact FOX for
inspection and repair.
Never attempt to pull apart, open, disassemble, or service a
FOX shock that is in a "stuck down" condition. A "stuck down"
condition results from a failure of the dynamic air seal (located
between the positive and negative air chambers within the
non-EVOL shock air sleeve), resulting with the negative chamber
retaining a higher pressure than the positive chamber. To test
whether the shock is in fact "stuck down":
• Remove the air cap and depress the Schrader valve,
• If the shock body retracts into the air sleeve near bottom-
• If the shock does not fully extend, it is in a "stuck down"
• Any attempt to service FOX air shocks in the "stuck
Installation on strut mount bikes may cause the air valve to hit
the reservoir unless reconfigured according to the user manual
instructions. Review user manual instructions using the QR
code below before installation. Check air valve orientation and
reservoir clearance with your frame before use. Failure to do so
may result in shock or frame damage.
3
to completely release air pressure from the positive
chamber of the shock.
out after the air is released from the positive chamber,
attach a FOX high-pressure pump and pressurize the
shock to 250 psi (17 bar).
condition.
down" condition can lead to SERIOUS INJURY OR DEATH.
Contact FOX or an Authorized Service Center for repair.