Scheppach HM80L Originalbetriebsanleitung Seite 35

8.2 Precision adjustment of the stop for crosscut
90° (fig. 5)
• No stop angle included.
• Lower the machine head (4) and secure it using the
locking bolt (25).
• Loosen the locking screw (23).
• Position the angle stop (A) between the saw blade
(6) and the rotary table (13).
• Loosen the lock nut (26a).
• Adjust the adjusting screw (26) until the angle be-
tween the saw blade (6) and rotary table (13) is 90°.
• Re-tighten the lock nut (26a).
8.3 Crosscut 90° and turntable 0° (fig. 1/2/3/6)
Important. To make 90° crosscuts, the adjustable
stop rail (8a) must be fixed at the inner position.
• Open the set screw (8b) for the adjustable stop rail
(8a) and push the adjustable stop rail (8a) inwards.
• The adjustable stop rail (8a) must be fixed far
enough in front of the innermost position that the dis-
tance between the stop rail (8a) and the saw blade
(6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (8a) and
the saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Move the machine head (4) to its upper position.
• Place the piece of wood to be cut at the stop rail (8)
and on the turntable (13).
• Lock the material with the clamping devices (15) on
the fixed saw table (9) to prevent the material from
moving during the cutting operation. See section
8.13.
• Release the lock switch (2) and press the ON/OFF
switch (1) to start the motor.
• Use the handle (3) to move the machine head (4)
steadily and with light pressure downwards until the
saw blade (6) has completely cut through the work
piece.
• When the cutting operation is completed, move the
machine head back to its upper (home) position and
release the ON/OFF button (1).
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not re-
lease the handle (3) after completing the cut; instead
allow the machine head to move upwards slowly
whilst applying light counter pressure.
8.4 Crosscut 90° and turntable 0° - 45° (fig. 1/2/3/6)
The cross cut mitre saw can be used to make crosscuts
of 0° -45° to the left and 0° -45° to the right in relation
to the stop rail.
Important. To make 90° crosscuts, the adjustable
stop rail (8a) must be fixed at the inner position.
• Open the set screw (8b) for the adjustable stop rail
(8a) and push the adjustable stop rail (8a) inwards.
• The adjustable stop rail (8a) must be fixed far
enough in front of the innermost position that the dis-
tance between the stop rail (8a) and the saw blade
(6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (8a) and
the saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Release the rotary table (13) by loosening the set
screw (7).
• Using the handle (3), set the rotary table (13) to the
desired angle.
• Retighten the set screw (7) in order to secure the
rotary table.
• Cut as described under section 8.3.
8.5 Precision adjustment of the stop for mitre cut
45° (fig. 1/2/3/6/7/8)
• No stop angle included.
• Lower the machine head (4) and secure it using the
locking bolt (25).
• Fix the rotary table (13) in the 0° position.
Important. For mitre cuts, the adjustable stop rail
(8a) must be fixed at the inner position.
• Open the set screw (8b) for the moveable stop rail
(8a) and push the moveable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far
enough in front of the innermost position that the dis-
tance between the stop rail (8a) and the saw blade
(6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (8a) and
the saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Loosen the locking screw (23) and use the handle
(3) to angle the machine head (4) 45° to the left.
• 45° - position angle stop (B) between the saw blade
(6) and rotary table (13).
• Loosen the locknut (22a) and adjust the adjustment
screw (22) until the angle between the saw blade (6)
and the rotary table (13) is precisely 45°.
• Re-tighten the locknut (22a).
• Subsequently check the position of the angle indi-
cator. If necessary, loosen the pointer (28) using a
Philips screwdriver, set to position 45° on the angle
scale (27) and re-tighten the retaining screw.
www.scheppach.com GB | 35