Salicru SPS ADVANCE R2 Betriebsanleitung Seite 43

5. INSTALLATION.
Read and respect the Safety Information, described in
•
chapter 2 of this document. Failure to obey some of the
instructions described in this manual can result in a serious or
very serious accident to persons in direct contact or in the vi-
cinity, as well as faults in the equipment and/or loads con-
nected to it.
During discharge, the equipment operates in IT (isolated
•
earth) neutral mode. This means that the neutral is not
directly connected to earth, providing an additional layer of
safety and stability in critical situations. To ensure optimal and
safe operation, follow the guidelines in the user manual and
contact your distributor if you have any questions.
5.1. RECEPTION OF THE DEVICE.
Pay attention to section 1.2.1. of the safety instructions
•
-EK266*08- in all matters relating to the handling, movement
and siting of the unit.
Use the most appropriate means to move the UPS.
•
Any handling of the device must be carried out in accordance
•
with the weights shown in the technical specifications according
to the model, indicated in chapter "9. Annexes".
5.1.1. Reception, unpacking and contents.
Reception. Check that:
•
The data on the label affixed to the packaging corres-
ˆ
ponds to that specified on the order. Once the UPS is
unpacked, check the previous data with those of the
equipment nameplate.
If there are discrepancies, file the disagreement as soon
as possible, citing the equipment manufacture number and
the delivery note references.
There is no damage to the packaging that may have oc-
ˆ
curred during transportation.
If there is damage, notify the carrier and indicate so on the
delivery note, and, as soon as possible, inform the supplier
/ distributor or, failing that, our firm.
Unpacking.
•
Remove the packaging to check the contents.
ˆ
Cut the seal and open the cardboard box.
–
Remove:
–
The bag containing cable or cables.
The bag containing ADVANCE R2 mechanical ele-
ments (angles, screws, etc.).
The input power cable.
Remove the device and plastic bag from the pa-ck-
–
aging and detach the protective corners.
Inspect the device before proceeding and, in the event
–
of finding damage, contact the supplier / distributor or,
failing that, our firm.
USER MANUAL
Do not leave any plastic bags within the reach of
children to avoid the danger of suffocation.
Disposal of the packaging must be carried out in accord-
ˆ
ance with current laws.
We recommend keeping it for at least one year.
Contents.
•
Device:
ˆ
1 UPS.
–
1 cable for the AC supply of the equipment (Schuko
–
type in its standard version and BS type for the UK
versions).
Information for warranty registration.
–
1 RS232 communication cable.
–
1 USB communication cable.
–
2 metal pieces for use as handles and screws for
–
installing the unit in a rack cabinet (only in SPS
ADVANCE R2 models).
Optional battery module (only in ADVANCE T models):
ˆ
1 battery module:
–
Information for warranty registration.
–
1 cable for interconnecting the battery module and
–
UPS or other module.
Once the reception is completed, it is advisable to re-pack the
•
UPS until it is put into service in order to protect it against me-
chanical shock, dust, dirt, etc.
5.1.2. Storage.
Equipment storage shall be done in a dry, ventilated place and
•
protected from rain, dust, water splashes or chemical agents.
It is advisable to keep each device and battery unit in its orig-
inal packaging, as it has been specifically designed to ensure
maximum protection during transportation and storage.
For devices that contain Pb-Ca batteries, the charging
•
times indicated in Tab. 2 of document EK266*08, de-
termined by the temperature to which they are exposed, must
be respected, otherwise the warranty may be invalidated.
After this period, connect the device to the mains together
•
with the battery unit if applicable according to the instructions
described in this manual and charge for 12 hours.
Then disconnect and store the UPS and batteries in their
•
original packaging, noting the new date for recharging the
batteries on a document as a record or even on the packaging
itself.
Do not store the devices where the ambient temperature ex-
•
ceeds 50ºC or drops below -20ºC, as this may cause degrada-
tion of the electrical characteristics of the batteries.
5.1.3. Transport to the site.
It is advisable to move the UPS using the most suitable means
•
for this. If the distance is considerable, it is recommended to
transport the device in its packaging to the installation site and
then unpack it.
SPS ADVANCE R2 & T UNINTERRUPTIBLE POWER SUPPLY (UPS)
43