Werbung
3 842 528 596 (03.09)
TS 1
Technische Daten · Technical data · Caractéristiques techniques
WT
= Werkstückträger
VE
= Vereinzeler
S ...
= Signalgeber
Y ...
= Ventil
Z ...
= Zylinder
HS
= Hauptstrecke
NS
= Nebenstrecke
= Startimpuls nach Anlaufende
= Freigabe zyklischer Ablauf
S1
= WT in Pos. an VE1/1 (Z1)
S2
= WT nach VE1/1 (Z1)
S3
= WT in Pos. auf EQ1
einschaltverzögert 100...200 ms
S4
= Freigabe Hauptstrecke 1
S5
= Freigabe Nebenstrecke
S6
= WT vor VE1/4 (Z4)
S7
= WT nach VE1/4
S8
= WT auf EQ2
S9
= Freigabe Hauptstrecke 2
S10
= WT vor VE1/5 (Z5)
S11
= WT nach VE1/55 (Z5)
Y1
= VE Hauptstrecke (Z1)
Y2.1/2.2 = Hub-Zylinder EQ (Z2)
Y3.1/3.2 = Hub-Zylinder EQ (Z3)
Y4
= VE Nebenstrecke (Z4)
Y5
= VE Hauptstrecke (Z5)
Y6
= VE in EQ (Z6)
P10
= Priorität
A1
= Geradeaussignal
Linear Motion and Assembly Technologies
WT
= workpiece pallet
VE
= stop gate
S ...
= signalling device
Y ...
= valve
Z ...
= cylinder
HS
= main section
NS
= branch section
= start pulse after end of approach
= enable cyclical sequence
S1
= WT in position at VE1/1 (Z1)
S2
= WT to VE1/1 (Z1)
S3
= WT in position on EQ1
switch-on delay 100...200 ms
S4
= enable main section 1
S5
= enable branch section
S6
= WT before VE1/4 (Z4)
S7
= WT after VE1/4
S8
= WT on EQ2
S9
= enable main section 2
S10
= WT before VE1/5 (Z5)
S11
= WT after VE1/5 (Z5)
Y1
= VE main section (Z1)
Y2.1/2.2 = lift cylinder EQ (Z2)
Y3.1/3.2 = lift cylinder EQ (Z3)
Y4
= VE branch section (Z4)
Y5
= VE main section (Z5)
Y6
= VE in EQ (Z6)
P10
= priority
A1
= straight-ahead signal
Bosch Rexroth AG
WT
= palette porte-pièces
VE
= séparateur
S ...
= transmetteur de signal
Y ...
= valve
Z ...
= vérin
HS
= circuit principal
NS
= circuit secondaire
= impulsion de départ à la fin du
démarrage
= libération des opérations en
cycle
S1
= palette en position sur VE1/1 (Z1)
S2
= WT vers VE1/1 (Z1)
S3
= WT en position sur EQ1
allumage retardé de 100...200 ms
S4
= libération du circuit principal 1
S5
= libération du circuit secondaire
S6
= WT avant VE1/4 (Z4)
S7
= WT après VE1/4
S8
= WT sur EQ2
S9
= libération du circuit principal 2
S10
= WT devant VE1/5 (Z5)
S11
= WT après VE1/5 (Z5)
Y1
= circuit principal VE (Z1)
Y2.1/2.2 = vérin de levage EQ (Z2)
Y3.1/3.2 = vérin de levage EQ (Z3)
Y4
= circuit secondaire VE (Z4)
Y5
= circuit principal VE (Z5)
Y6
= VE en EQ (Z6)
P10
= priorité
A1
= signal direct
12–21
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Werbung
