Storage; Disposal And Recycling - Scheppach MPT3400-4PGE Anleitung

Ordering replacement parts
Please quote the following data when ordering
replacement
parts:
• Type of machine
• Article number of the machine
Replacement parts / accesories:
For the cutting equipment listed here, you can always
use the safety guards provided with the unit.
Grass trimmer/brush cutter:
Spool with Ø 450
Blade with 3 teeth Ø 255 x 1.4
Transport guard for blade 3 teeth
Blade with 4 teeth Ø 255 x 1.4
Transport guard for blade 4 teeth
Blade with 8 teeth Ø 255 x 1.4
Transport guard for blade 8 teeth
Safety shield for grass trimmer
Pole pruner:
Saw chain ProCut 3/8.50-39
Guide rail ProCut AL10-39-507P
Saw chain Oregon 91PJ040X
Guide rail Oregon 100SDEA318
Transport guard for chain
Extension for pole pruner
Hedge trimmer:
Blade for hedge trimmer 400 mm
Transport guard for blade

11. Storage

Cleaning
• Keep handles free of oil, so you always have a secure
hold.
• Clean the equipment as required with a damp cloth
and, if necessary, mild washing up liquid.
m Important!
• Always pull out the spark boot plug each time
before carrying out any cleaning.
• Never immerse the equipment in water or other
liquids in order to clean it.
• Store the petrol multi garden tool in a safe and dry
place out of the reach of children.
Storage
Important: Never put the equipment into storage for
longer than 30 days without carrying out the following
steps.
Storing the equipment
If you intend to store the equipment for longer than
30 days, the equipment must be prepared according-
ly. Otherwise the fuel still remaining in the carburetor
will evaporate and leave a rubbery sediment. This
can cause problems when starting up the equipment
and may require expensive repairs.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
1
2
3
4
5
Note: Store the equipment in a dry place and far
7910700701
away from possible ignition sources such as an oven,
7910700702
a gas-fi red hot water boiler, a gas-fi red dryer, etc.
3904801065
7910700705
3904801066 Putting the equipment back into operation
7910700711
1
3904801066
3904801023
2
7910100732
3
7910100731
7910700704
3904801037
4
3904801039
7910700710
Transport
If you want to transport the tool, empty the petrol tank
7910700703
as described in Chapter 8. Remove major dirt from
the unit with a brush.
3904801043
Always attach the transport guard to all cutting tools.
Fig. 1 (14a, 15a, 17a)
In order to prevent damage and injury, secure the
tool against tipping over and sliding when transport-
ing it in vehicles.

12. Disposal and recycling

Defective components must be disposed of as
special waste. Ask your dealer or your local council.
Slowly remove the fuel tank cap to release any
pressure that may have formed in the tank. Care-
fully empty the tank.
To remove the fuel from the carburetor, start the
engine and let it run until the equipment stops.
Leave the engine to cool (approx. 5 minutes).
Remove the spark plug (see section 10 Change
and clean the spark plug).
Add one teaspoon of 2-stroke engine oil into the
combustion chamber. Slowly pull the starter cord
several times to apply a layer of oil to all internal
components. Fit the spark plug again.
Remove the spark plug (see section 10 Change
and clean the spark plug).
Quickly tug on the starter cord to remove excess
oil from the combustion chamber.
Clean the spark plug and check that the electrode
gap is correct, or insert a new spark plug with the
correct electrode gap.
Prepare the equipment for operation.
The equipment is supplied in packaging to
prevent it from being damaged in transit.
The raw materials in this packaging can be
reused or recycled. The equipment and its
accessories are made of various types of
material, such as metal and plastic.
GB | 41