Cleaning; Transport & Storage; Maintenance - Scheppach RS350 Original Bedienungsanleitung

11. Cleaning

Attention!
Disconnect the mains plug before starting to clean
the device.
We recommend that you clean the device directly af-
ter every use.
Drum cleaning
Take off soil from the drum after every use. The run-
ning surface of the vee-belt on the drum must always
be kept clean. Soil and stones ruin the vee-belt.
12. Transport & storage
Transport and storage, Fig. 6
• Turn the device off, disconnect it from the mains
and remove coarse soil.
• Loosen the angle ratchet and the knob and put the
sieve drum in the transport position in a controlled
manner. Ensure that the sieve drum does not sud-
denly move downwards in an uncontrolled way.
Otherwise, the device can become damaged.
• Secure the sieve drum in the transport position
with the safety splint, by doing the splint put into
the bore of angle sheet and drum frame.
• Now you can transport the device easily and store
it without much space requirement. Make sure the
storage area is dry.
Store the device and its accessories in a dark, dry
and frost-free place that is inaccessible to children.
The optimum storage temperature lies between 5 and
30 ˚C.
Store the device in its original packaging.
Cover the device to protect it from dust or moisture.
Store the operating manual with the device.

13. Maintenance

Attention!
Disconnect the mains plug before carrying out any
maintenance work.
Conduct maintenance and cleaning works only with
the unit shut off and the power supply plug pulled.
Adjusting the brush bar
If required, adjust the brush bar on the roller sieve. To
do this, loosen the three screws and push the brush
bar into the required position. Then hand-tighten the
three screws again.
Belt tension drive, Fig. 8
After a period of use, the drive belt can extend or
suffer from wear and tear. This will prevent reliable
power transmission from the motor to the sieve drum.
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
You have to re-tighten the drive belt or replace it.
• Unscrew the motor drive cover (Fig. 1-7).
• Adjust the flat belt tension by loosening the three
motor screws (A) and push the motor upwards.
• If you cannot tighten the belt, or/and it is porous, it
is worn and you have to replace it.
• Hold the motor with one hand and hand-tighten the
motor screws with the other hand.
• Tighten the motor belt cover again.
Belt tension drum, Fig. 9
After a period of use, the drum belt (Fig. 1-11) can
extend or suffer from wear and tear. This will prevent
reliable power transmission from the drive wheel to
the sieve drum. You have to re-tighten the drive belt
or replace it.
• Unscrew the drum belt cover (Fig. 1-12).
• Loosen the bearing screws (A) and adjust the
bearing accordingly.
• If the belt cannot be tightened, and/or it is porous,
it is worn and you have to replace it.
• Hand-tighten the bearing screws again afterwards
and re-attach the drum belt cover to the casing.
WARNING!
Do not store the device without protection out-
side or in a damp environment.
Connections and repair work
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the
event of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Engine data - type plate
Service information
With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Spare parts*: Driving and driven belts, sieve inserts,
driving bars, collecting mat
* may not be included in the scope of supply!